2009 Dodge Journey Logo

Related Topics:

t
tony martin Posted on Jan 16, 2014
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Rear door glass removal

I have a customer that wants rear door glass removed because he wants the privacy glass replaced with factory tint glass. I cannot get the glass out of the opening. Please help

1 Answer

mjbat

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 220 Answers
  • Posted on Jan 16, 2014
mjbat
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: Nov 06, 2009
Answers
220
Questions
0
Helped
67020
Points
618

After you get the regulator assembly out of the way try removing any tracks inside the door that can be removed and see if you can then rotate the glass.

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jun 25, 2008

SOURCE: Lift gate glass

We ended up using a wire attached to 2 wooden handles passing through the gasket material between the glass and the metal frame and sawing the gasket. Quite a slow job but it worked. As far as the handle goes it'll probably be a case of breaking the plastic hex bolt that holds the assembly and replacing it or maybe the whole thing.

Ad

Anonymous

  • 405 Answers
  • Posted on Dec 14, 2008

SOURCE: Replacing visor courtesy mirror glass

two solutions, One www.car-parts.com or go to glass shop and see if they can repair it.

Anonymous

  • 103 Answers
  • Posted on Jan 10, 2009

SOURCE: 1991 dodge dynasty rear window removal

I have never been able to remove sealed in glass without breaking it. But in theory if you can get a guitar string through the sealant and pull it through like a cable saw you might get it out. I've tried 15 times, and have 15 broken windshields to show for it. good luck

Anonymous

  • 854 Answers
  • Posted on Sep 24, 2009

SOURCE: how do you remove the rear glass on a 1997 dodge

You can start by pulling the interior back by the rear window. There are two tabs on both ends on the bottom frame, you can bend them straight.Try to pull the bottom of the window out and watch out for the hinges to carefully lift up the window itself.

Anonymous

  • 493 Answers
  • Posted on Jun 18, 2012

SOURCE: how to remove tint and glue from side windows w/o ruining glass

Sharp razor blade. You can buy them from an auto shop pack of 5 - 100 i think. Takes ages but you just scrap the tint off. I have asked a tint shop 1/2 way through ding this & they advised me that was the corect method.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How to repair back window

If mean how to tint the rear window, The tint goes on the inside. I would remove the plastic rear door cover to start with because you will already be working over your head, after that thoroughly cleaning window with a vinegar based window cleaner, cut film at least 2 inches extra on each side (4 inches added to the widest and tallest measurement) spray water onto window with spray bottle, center film start in center with soft rubber squeegee pushing water and air bubbles out while leaving all 4 sides loose so more water can be sprayed onto window as you work your way out trim excess tint off with razor re-install door panel.
0helpful
1answer

How to remove tint and glue from side windows w/o ruining glass

Sharp razor blade. You can buy them from an auto shop pack of 5 - 100 i think. Takes ages but you just scrap the tint off. I have asked a tint shop 1/2 way through ding this & they advised me that was the corect method.
0helpful
1answer

How do I take the front window out of a junk yard 1992 cadillac sedan de ville ( no battery) without riping the tint?

I would worry about saving the glass from breakage. The tint will get scratched no matter how its removed. By the way most states ban tinted windows on the front doors of all vehicles. That is why the rear windows from the factory are tinted with the exception of Wisconsin. They ban tinted windows period
0helpful
1answer

I need to remove a rear door gllass on a lexus Gs

Remove rear door panel, reconnect power window switch, looking at bottom edge of glas you should see two 10mm bolts roll down window until bolts are accessible. Remove bolts and tilt window around 10 degrees top edge out/in. if still to tight to slide out put glass in lowest position and remove window frame weather stripping and it should slide right out the top, careful not to scratch tint.
0helpful
1answer

How do I remove the tint of my rear window in my 1998 chevy Malibu?

If it has a rear window defroster, you can't use a razor blade. If the tint material will pull off and leave glue behind, then spray windex on the glass and put the tint material back on the glass like it was. Can't do this in the sun to long, the sun will dry out the windex. The ammonia in the windex will loosen up the glue. Then you can remove the tint material, and the glue should wipe of with a paper towel.
p.s. let the windex soak for 5 min. or so.
1helpful
1answer

How do i replace left door mirior

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
0helpful
2answers

Windows tint

If it's factory tint, it is imbedded in glass and can't be removed.
If it's add on tint, it is just a plastic film on inside of glass.
Call a tinting shop and ask what chemical to spray on film to soften adhesive, or ask for removal quote too
0helpful
1answer

Tinting the rear door glass geting to the edges

usually make cut out template of window then cut tint to template then fit and work into tight spots while fitting.New sharp razor blades and a steady hand.
1helpful
3answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...

  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor
0helpful
1answer

Side windows

It may seem easier to tint them out of the suv, but it is very easy to damage them putting them back in. pre-cut the tint material on the outside of the glass. Make sure you have the tint on the correct side when pre-cuting. leave a 1/32 gap around the tint edge when pre-cuting. That will keep the tint from binding up around the edges. Also the soapy water has a way to escape. Make sure the glass is as clean as possible.
Not finding what you are looking for?

1,635 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...