If your service engine light on what would be the first thing would you change first oxygen sensor ignition misfired fuel problem or the purge or vent solenoid failure plugged evap canister condition pressure sensor

codes are OBDll and are available online free
P0174

• Intake air leaks
• Faulty front heated oxygen sensor
• Ignition misfiring
• Faulty fuel injectors
• Exhaust gas leaks
• Incorrect fuel pressure
• Lack of fuel
• Faulty Mass Air Flow (MAF) sensor
• Incorrect Positive Crankcase Ventilation (PCV) hose connection
• P0171
• Intake air leaks
• Faulty front heated oxygen sensor
• Ignition misfiring
• Faulty fuel injectors
• Exhaust gas leaks
• Incorrect fuel pressure
• Lack of fuel
• Faulty Mass Air Flow (MAF) sensor
• Incorrect Positive Crankcase Ventilation (PCV) hose connection
• P0102
• copy and paste
• https://www.justanswer.com/ford/2dnqt-98-windstar-dtc-p0102-sitting-trouble-code-mil.html

copy and paste
https://www.justanswer.com/ford/8kg47-ford-windstar-code-p0302-p0305.html

P0453
copy and paste
https://www.justanswer.com/ford/3qxa3-getting-po453-code-evap-pres-sensor-high-99-windstar.html

There is a technical service bulletin that states the correct procedure to repair this issue is to replace the injectors with updated units AND reprogram the pcm for the new injectors.

P0303 Code - Cylinder #3 Misfire
P0110 DTC - IAT Circuit Malfunction
P2195 O2 Sensor Signal Biased/Stuck Lean (Bank 1 Sensor 1) Code
Potential causes of a P2195 code include:
p2195
p219521

• Oxygen (O2) or A/F ratio sensor or sensor heater malfunction
• Open or short in O2 sensor circuit (wiring, harness)
• Fuel pressure or fuel injector problem
• Faulty PCM
• Intake air or engine vacuum leaks
• Faulty fuel injector(s)
• Fuel pressure too high or too low
• PCV system leak/fault
• A/F sensor relay faulty
• MAF sensor malfunction
• ECT sensor malfunction
• Fuel pressure too low
• Fuel leak
• Air suction in air intake system
• A code P0303 may mean that one or more of the following has happened:
  

• Faulty spark plug or wire
• Faulty coil (pack)
• Faulty oxygen sensor(s)
• Faulty fuel injector
• Burned exhaust valve
• Faulty catalytic converter(s)
• Running out of fuel
• Poor compression
• Defective computer
• Potential causes of the P0110 DTC include:
  
• 
  po110
  • IAT sensor shifted out of airflow
  • Bad IAT sensor
  • Shorted to ground or open on signal circuit to IAT
  • Open in ground circuit to IAT
  • Poor connection at IAT (backed out terminals, broken connector locks, etc.)
  • Bad PCM

Well the P0300 code has nothing to do with your O2 sensors just a heads up.

P0300: Random/Multiple Cylinder Misfire Detected

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor (POS) signal to vary, Powertrain Control Module (PCM) or Electronic Control Module (ECM) can determine that a misfire is occurring.

Causes:
- Improper spark plug
- Insufficient compression
- Incorrect fuel pressure
- The injector circuit is open or shorted
- Fuel injectors may be faulty
- Intake air leak
- The ignition signal circuit is open or shorted

Solutions:
- Perform Injector Service
- Replace Spark Plugs
- Replace Injectors
- Replace Ignition Coils

P0135: O2 Sensor Heated Circuit Malfunction Bank 1 Sensor 1

The front heated oxygen sensor (or sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the ECM. The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Causes:
- Harness or connectors (The sensor circuit is open or shorted)
- Front Heated oxygen sensor (Bank 1) may be faulty

Solutions:
Replacing the O2 Sensor 1 usually takes care of the problem

How did you read that code on your car? A 92 Accord is supposed to give you pre-OBD honda codes, which are all below 100. Please check the code again and re-post it.

Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

U have to operate the engine at all kinds of diff speeds and drive modes, it is called a OBDII drive cycle, here is how u do one.
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge

It is either your Vehicle Speed Sensor (easy to change) or your Automatic Transmission Computer (capacitors burn out on these boards, there is a fix for this too, the picture is at the bottom of this page). You need to diagnose by removing the lower right plastic kick panel on the passenger side. There you will find a blue plug. With the car OFF stick a paper clip, wire or stuff the plug with foil to make electrical connection so that the two terminals are touching. Then, turn the ignition to ON (not enough to start it though, just power it up). When you do this, count the blinks in the "D Light" or count your blinking Check Engine Light. Both are different but can refer to different things wrong with your car. A long blink is the first number and the short blinks that follow are the second number.
So imagine this as being 14 : ___ _ _ _ _

Below is a decoding chart:

The first section will be the check engine light codes, the next one is the Transmission Control Unit Codes read from the D Light;

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input
92 Evaporative Emission Control System insufficient purge flow

TCU Codes:

CODE LIST:

1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

It is either your Vehicle Speed Sensor (easy to change) or your Automatic Transmission Computer (capacitors burn out on these boards, there is a fix for this too, the picture is at the bottom of this page). You need to diagnose by removing the lower right plastic kick panel on the passenger side. There you will find a blue plug. With the car OFF stick a paper clip, wire or stuff the plug with foil to make electrical connection so that the two terminals are touching. Then, turn the ignition to ON (not enough to start it though, just power it up). When you do this, count the blinks in the "S Light" or count your blinking Check Engine Light. Both are different but can refer to different things wrong with your car. A long blink is the first number and the short blinks that follow are the second number.
So imagine this as being 14 : ___ _ _ _ _

Below is a decoding chart:

The first section will be the check engine light codes, the next one is the Transmission Control Unit Codes read from the S Light;

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input
92 Evaporative Emission Control System insufficient purge flow

TCU Codes:

CODE LIST:

1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

It is either your Vehicle Speed Sensor (easy to change) or your Automatic Transmission Computer (capacitors burn out on these boards, there is a fix for this too, the picture is at the bottom of this page). You need to diagnose by removing the lower right plastic kick panel on the passenger side. There you will find a blue plug. With the car OFF stick a paper clip, wire or stuff the plug with foil to make electrical connection so that the two terminals are touching. Then, turn the ignition to ON (not enough to start it though, just power it up). When you do this, count the blinks in the "D Light" or count your blinking Check Engine Light. Both are different but can refer to different things wrong with your car. A long blink is the first number and the short blinks that follow are the second number.
So imagine this as being 14 : ___ _ _ _ _

Below is a decoding chart:

The first section will be the check engine light codes, the next one is the Transmission Control Unit Codes read from the D Light;

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Fuel Tank Pressure Sensor low input
92 Evaporative Emission Control System insufficient purge flow

TCU Codes:

CODE LIST:

1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.