1996 Jaguar XJ6: Diagnostic (Check Engine) Camshaft Sensor A

The camshaft position sensor on a Peugeot 3008 can be located in different positions depending on the engine model and year of manufacture. Here are the possible locations:

1. On the engine cylinder head: In some Peugeot 3008 models, the camshaft position sensor is mounted on the engine cylinder head, near the camshaft.
2. Near the timing belt cover: In some other models, the camshaft position sensor is located near the timing belt cover. It can be either on the engine block or on the cylinder head.
3. Behind the camshaft pulley: In some Peugeot 3008 models, the camshaft position sensor is located behind the camshaft pulley.

To locate the camshaft position sensor on your specific Peugeot 3008 model, you should consult your owner's manual or a repair manual for your vehicle. Alternatively, you can seek the assistance of a professional mechanic or a Peugeot dealer.

Immobiliser system can cut spark..check this is operating correctly

Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Hi, my name is John I will do my best to assist you.

To Remove

1. Disconnect the negative battery cable.
2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
3. For SOHC engines, remove the air cleaner inlet tube.
4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.

To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
5. Install the air cleaner inlet tube and the filtered air tube.
6. Connect the negative battery cable.

The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown



Location of the camshaft position sensor - DOHC engine shown



Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar



The target magnet has 2 locating dowels for proper alignment during installation

Removal & Installation 2.0L engine camshaft position sensor location

2.4L engine camshaft position sensor location

2.0L SOHC Engine To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Brake booster hose and electrical connector from holders on end of cylinder head cover and reposition
   • Electrical connectors from camshaft position sensor
   • Camshaft position sensor mounting screws
   • Sensor

To Install:

1. Install or connect the following:
   • Camshaft position sensor. Torque sensor mounting screws to 80 in. Lbs. (9 Nm)
   • Brake booster hose and electrical harness in holders on end of valve cover
   • Electrical connectors to camshaft position sensor

2.4L Turbo Engine To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Air cleaner box
   • Plastic clip for the wiring harness from the stud on the valve cover
   • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose from the valve cover
   • Electrical connectors from camshaft position sensor
   • Camshaft position sensor mounting screws
3. Remove sensor

To Install:

1. Install or connect the following:
   • Camshaft position sensor torque sensor mounting screws to 80 in. lbs. (9 Nm)
   • Electrical connectors to camshaft position sensor
   • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose to the valve cover
   • Plastic clip for the wiring harness to the stud on the valve cover
   • Air cleaner box
   • Negative battery cable

What engine ? 2.2 or 3.1 ?

This 3.1 L back center of engine

I have had a similar problem and found that the centre wire from coil to distributor cap had slipped back just far enough from inside the coil to not make a good connection..and no spark meant cranking but no spark to plugs...

Jeep Patriot Crankshaft Position Sensor replacement ...

? 9:09
https://www.youtube.com/watch?v=omwDHaBGUEc
Jan 15, 2012 - Uploaded by JasonthePCMD
Here's how to replace the Crankshaft Position Sensor (CKP) on a 2008 and newer Jeep Patriot, Compass ...

Jeep Cherokee camshaft crankshaft sensor how to replace ...

? 2:59
https://www.youtube.com/watch?v=oOc1Lxod2x8
May 17, 2012 - Uploaded by unpescad0
How to locate and install a new camshaft and or a crankshaft position sensor. This vehicle is a 2001 Jeep ...

Crankshaft position sensor location - Jeep Patrio

camshaft sensor is in distributor(requires dist. replacement) crankshaft is behind lower timing belt cover