Security system 2005 caravan

SOURCE: Security System on 2005 Dodge Ram 1500 malfunctioning

if you do not want to go back to the dealer then take it to an alarm shop which does private installations on cars and trucks because most of the time when they install after market alarms they bypass them or just pull out the factory alarm altogether.

SOURCE: Airbag dash light

Transport Canada Vehicle Recalls & Defects Database Transport Canada Recall # 2007169 Recall Date:  2007/05/30 Notification Type:  Recalls Audit System:  Airbag Manufacturer Recall Number:  G09 Units Affected:   51,000 Category: Minivan Recall Details: On certain vehicles the left or right front supplemental airbag sensors may crack under certain conditions, which can allow water to enter into the sensor. This can cause the airbag warning lamp to illuminate. A malfunction of one or both of the supplemental sensors will not adversely affect safety or cause a failure to comply with government standards. The single-point sensor in these vehicles, which is located in the airbag control module, is operational even if both supplemental sensors are inoperative. DaimlerChrysler has decided to launch a Customer Satisfaction Notification to advise customers that these front airbag sensors will be replaced with redesigned sensors to reduce the potential for damage. This action is not being conducted under the Motor Vehicle Safety Act.

SOURCE: 2001 caravan light problem

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}You need to check if flasher module is workingproperly. It is located on the junctionblock, adjacent to and left of the steering column. To access the junction block, first removethe lower steering column and keen pad panel. When the flasher module is functioning properly, a click can be heardduring its operation. If the turn signals fail on one side or the other and theflasher module doesn’t make its characteristic clicking sound. A faulty turnsignal bulb is indicated. If a rapidly flashing turn single is observed, alight is burned out of there is a loose or open connection to a light. When the ignition is ON, the front turnsignals are ON steadily (not flashing) for the Daytime Running Light, and flashonly when the turn signals of hazard flasher are operated. ///////I would recommend that you change the flasher module.I have taken every thing out of the repair manual above.//////

SOURCE: 2003 dodge sxt caravan start my van and stop after 3 sec

replace the ignition unfortunetly thats probably going to be the fix

SOURCE: REMOTE KEYLESS ENTRY 99 GRAND CARAVAN

INSTALLATION: REMOVE THE TOP DASH COVER USING A FLAT TIP SCREW DRIVER AND LOCATE THE CONNECTOR FOR THE RKE MODULE. THE CONNECTOR WILL BE SMALL AND LOCATED NEXT TO THE HVAC DISTRIBUTION DUCT. MOUNT MODULE AND INSERT THE CONNECTOR. SINCE THE BODY CONTROL MODULE IS INVOLVED WITH THE RKE THIS MAY OR MAY NOT WORK BECAUSE NOT ALL CONTROLLERS ARE THE SAME BUT IF YOU WOULD LIKE TO TRY TO PERFORM THE TASK TRY THIS. FOR PROGRAMMING:

1. Using a functional key fob transmitter, unlock the vehicle and disarm the Vehicle Theft Security System.
2. Insert ignition key into the ignition switch.
3. Turn the ignition switch to RUN position without starting engine.
4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum four seconds (maximum ten seconds)
5. While holding UNLOCK button, and before ten seconds passes, press and release the PANIC button. A single chime will sound to verify that the RKE module is set to receive the new Vehicle Access Code(s)
6. Within 30 seconds of the chime, press and release the "LOCK" and "UNLOCK" buttons on the transmitter at the same time. Then press any one of the buttons. The BCM will sound an abbreviated chime to acknowledge that the programming of the transmitter has been completed and was successful.
7. Repeat step 6 for all transmitters that will be used with this vehicle (up to 4 total)
8. Programming mode will last for 30 seconds. To get out of programming mode sooner, turn the ignition OFF. A single chime will sound to verify that the RKE module will no longer accept additional Vehicle Access Code(s)
9. When Vehicle Access Code(s) programming is complete, turn the ignition switch to the OFF position and verify RKE system operation using each key fob