Is Spring Gate Closer use any internal mechanism or hydraulic system to close the door?

Check to see if the latches didn't already close.
Sometimes the latch spring closes the latch prematurely
If you look on the side of the door where the latch is located.
It has 2 pieces of metal that look like small jaws in the sideways letter W or C when it is open.
However if it's closed it will either look like a small o or metal to metal.
Then what you will need to do is have someone hold the door handle to the open position.
Take a good sized regular screwdriver and put it between where the latch metal meets.
It should start to separate without much pressure and you will see what I mean.
Then use the screwdriver to open it fully.

I think you'd try spring Gate Closer system because they are not heavy as compare to hydraulic door closer system and close the door not forcefully as other door closer system.And it's easy to install. http://www.gateshut.net/about-gate-closer.html

Yes i know a company who can deal in door closer system.Surely they will solve your problem.http://www.gateshut.net/buy-your-gate-closer-here/gate-closers/medium-gate-closer-for-farm-and-ranch-gates.html

Try pressing the door closed while unlocking and releasing. If the door previously has been slammed shut hard or just due to general wear and tear the latching mechanism can become slightly relocated. This means that when the door closes the door is pressing tighter than normal against the door seal. The compressed door seal will put a lot of strain on the latch mechanism and can hinder its retraction when released. By pressing the door closed and therefore removing the strain due to the door seal you might allow the release mechanism enough freedom of movement to retract when released. If having got the door open then immediately adjust/relocate and lubricate the lock/release mechanism such that you achieve a happy medium of the door closing with a weatherproof seal but not so tightly as to put the latch under a lot of strain.

Look at the door's locking mechanism. Is the Latch Gate in the down position? Is the Door Mechanism properly tightened to the door? These are Torx/Hex head bolts. Tighten these if needed.
If the Latch Gate is down:
1. Unlock the door.
2. Lift up/out on the Door Handle as if you were opening the door.
3. Use a screwdriver to lift the Latch Gate so it lifts the Gate up and out of the way.
Alot of these Gates have plastic coverings that sometimes split and stick or cause the door mechanism to jam. Inspect the Door Mechanism for anything that could be causing it to jam. Using a pair of needle nose pliers remove any of this split plastic (if so equipped) pulling as much of it off the Latch Gate.
Use WD40 with the red spraying hose on and stick it as many openings you can and lubricate as much of the Door Mechanism as you can.
Check the operations (plural) of the Door Mechanism, Opening and Closing the Gate using the screw driver to push in the Striker Gate causing the Latch Gate to rotate back down into position. Repeat... checking for the Latch Gate to Release Up (on it's own) when you "open" the door. If it doesn't, then there is either jammed or a return spring is broken.
Have you dented or distorted the Door and / or Door Mechanism in the process of trying to slam the door close? You will have to either bend the the door area back to as close to possible the original shape. Use the other door on the other sides as a guide on this. You may have to replace the Door Mechanism itself, as when they are malfunctioning and are slammed (over and over) it could break the Mechanism itself. If the Mechanism is broke, you will have to remove and replace the entire mechanism.
Let me know if this helped, or if you have additional information of questions. Feel free to conatct me at FixYa.com!

the door lock mechanism has a broken spring internally .door lock has to be replaced.

I spend the next 10 minutes alternating between randomly hitting the FOB’s lock and unlock buttons, until I give up in a garage-filling string of expletives as I realize my kayak and I are SOL. Luckily, I did have a friend and an incredibly helpful REI employee there, whom all pitched in and managed to jam the kayak into the Suburban through the side door. I love my Suburban for reasons like this, though I’m slowly starting to hate GMC. More on this to come.
Here’s the Suburban with kayak inside and the lift gate panel on the floor. If you have a Suburban / Tahoe / Yukon in the same situation where your lift gate won’t open, the only way to get it open is to pry the lift gate panel just enough to access the locking mechanism. Take a long flat head screwdriver, slip it into the top section of the panel and start pulling away. The panel is made of a flexible plastic that will bend a fair amount, so don’t be afraid to put a bit of elbow into it. Once you see the locking mechanism, you’ll want to grip the back side that moves and twist counter-clockwise until the door pops open. Once you’ve done this, call GM customer service and tell them that their engineers should be fired for not having a manual release. If there is an accident / fire up front, wouldn’t you like it if your kids could escape out the back? Yeah, me too.
If you’re lucky enough that you can open your door (or maybe it doesn’t lock to begin with), then it’s a little easier to pull off the panel. First, take a socket wrench (9mm, I think) and remove the bolt under the leather handle on the inside of the door (the one you pull down on when your lift gate is up). After that, insert a flat head into the space between the panel and the door and pry open. There will be around 4 or 5 contact points to disconnect.
The two last things that stand in your way are plastic hinges that hold the panel to the door frame. With the lift gate open, push the panel toward the car, then spin it an entire half-circle around the hinge in the picture. After that, the panel should pull right out. Now the locking mechanism should be nicely exposed.
Here we see the lift gate handle at the bottom, which is connected by a tension wire to the locking mechanism. Pulling on the handle causes the wire at the top to retract toward the right, turning the locking mechanism counter-clockwise.
However, pulling the handle does nothing when the mechanism is in the locked position, because it doesn’t engage the other tension wire / tailgate release - it just simply moves by itself. When the mechanism is unlocked, pulling on the handle will engage the release mechanism and pop open the door… when the locking mechanism is working, that is.
Here is a properly unlocked door: notice that the black plastic piece (on top of the copper) is slid all the way to the right. You can see that if you rotate the lower copper piece, that it will force the black plastic piece to turn, thus engaging the door release.
Here is why your Suburban tailgate won’t unlock. I’ve just pressed the unlock button on my key FOB and you can see that the black plastic piece has NOT slid over to the right. This means that the door is still LOCKED as far as the mechanism is concerned. No amount of yanking on the handle will open the lift gate at this point.
Zooming in for a close-up, you can really see where the problem is. Gear heads will realize this is a major problem for all sorts of reasons. First, if your door lock actuator is banging against this metal part every time you unlock your door, it will wear out the part extremely fast and you’ve got yourself a busted door. Second, even if you replace your actuator, you’ll just bust it again if it keeps ramming this part. Most importantly, the question is how this is happening to begin with? My Suburban was working fine until I put in a factory replacement handle.
My opinion is that the factory GM replacement was defective and not built to spec, because the tensioner was now pulling a few millimeters more than it should have, which resulted in my lift gate not closing or unlocking. While millimeters might not mean anything to some cheap factory in China or Mexico, it means a whole lot of difference to the Joe Schmoe who wants to have a car that works. It may also be due to a small and very important spring that resets the lock back into place.
I’ve read a whole ton of reports about Suburban lift gates, along with Tahoes, Yukons and other GM cars failing and drivers stuck with unlockable doors. I believe this type of careless “few millimeters off isn’t important” BS is likely to blame. That’s why some people may have locks that work only half the time, or some work after their actuators are replaced, but fail soon afterward. My two-cent opinion - back to fixing cars.
So what we need to do, is make some space for that locking (technically, “unlock”) mechanism to engage fully. On my Suburban, this meant giving the metal tensioner just a little more slack - 2mm would be all I need.
First, I pushed the handle wire mechanism over to the right and then pulled out the metal ball and wire. After that, I pinched the blue wire cap and pushed it out of the metal holder.
You can now see that there is a lot of visible space between the locking mechanism and the metal. Pressing lock and unlock on my key FOB easily moved the unit back and forth successfully, so I knew it wasn’t a problem with the actuator. Now comes the disclaimer part.
DISCLAIMER: Attempt this section at your own risk, you are responsible for your own actions!!! Not seeing a lot of options, I decided I would take a somewhat drastic approach and bend the wire holder closer to the locking mechanism with a pair of pliers. I only needed about 2mm, so I felt this was acceptable without busting the car too much. Needless to say, this is not a graceful fix nor one I really wanted to do, but there appeared to be little other options other than cutting your own tensioner line (adjusting the line would be the most logical method, but I pinching and pulling got me no results) or finding some concrete way of bracing the line closer to the locking mechanism. If you come up with an elegant solution, please let me know.
Phew, finally - the fixed tailgate lock! You can see there is just enough room for the mechanism to engage and that the handle tension wire is snugly seated into its new home. I tested the lock about 100 times to be sure that everything was working as it should and I advise you do the same once you get to this point.
Now, simply put the panel back on the same way you took it off (don’t forget to screw the bolt back into the handle) and you’re done. Have a beer and go pat yourself on the back.
If this blog post has helped at all, I’d appreciate if you left a comment to share you experiences so others in the same situation can hear what you did. Thanks.

i had this problem. I had a lock smith open the interior panel on the rare door he removed the lock mechanism and tripped the switch it engaged to allow the door to open and the lock to close again properly. it cost me $45.00. you might have a bad mechanism and need it replaced. I accidently hit the latch and caused it to be in the lock position so i was not able to completely close the gate.

Unfortunately, you will have to remove the panel of the door, Use flathead screwdriver to pry open. It is very likely the spring fell off.

hi there,

this can be stuck contacts on the door. better to check the sliding contact point for any dirt debris on the slide or it may need some lubricant for easily sliding.