2007 BMW 328xi Sports Wagon Logo

Related Topics:

A
Anonymous Posted on Dec 30, 2012
Be the first to answer

Removal and installation of tail light lens bmw 528 wagon 2000

Removal and installation of tail light lens

Answer This Question

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jun 26, 2008

SOURCE: installing struts on 1999 528 BMW

haynes manual

Ad

Anonymous

  • 5 Answers
  • Posted on Jun 29, 2009

SOURCE: 2000 bmw 323i always displays -40 degrees

You ripped out your outside temperature sensor, it's located by the  right brake duct area.

Anonymous

  • 242 Answers
  • Posted on Oct 26, 2009

SOURCE: replace left tail light assembly on 2003 325i

If you pull back the carpet in the trunk directley behind the lens, you should find the mounting screws. Some models only need to have a few plastic wing nuts removed without pulling back the carpet.

Anonymous

  • 30 Answers
  • Posted on Nov 28, 2009

SOURCE: How doI turn off the oil light on a 528 2005 bmw

needs to be put on computer to turn off fault light

Anonymous

  • 2 Answers
  • Posted on Feb 13, 2010

SOURCE: bmw 528 oil service light needs to be reset . Any

BMW's from 82' to 2001 should have a 20 pin connector under the hood. Unscrew the lid and find pins 7 and 19. Short these pins together and turn the key to run, not start. Within 5 to 10 seconds the sensor will reset. Leave the key on, and remove the short. Don't leave them shorted too long, as this will reset the maintenance interal.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to remove tail light lens on 2000 ford contour SE
Open the trunk. Pull back the trunk lining where it covers the tail light access inside the quarter panel. Remove the lamp sockets for the turn/stop and backup lights, and remove the screws that hold the lens in place. The lens will then pull out from the quarter panel. Installation is the reverse: make sure the rubber gasket is in place properly.
Read full answer
Jan 28, 2013 • 2000 Ford Contour
tip

How to Fix Foggy Tail Lights in BMW 528 car?
1) Stick the masking tape and paper around the tail light to take care of the paint. 2) Take care nothing gets rubbed on the car paint or nothing gets scratched on the car light cover and paint. 3) Do it gently without any force. 4) Take a sand paper make it wet and use the wet sand paper to sand the tail lights. 5) Do this sanding until all the dirt and fogginess is removed completely. 6) You can use heavy grit sand paper if the dirt is very hard to remove. 7) After sanding is done clean and rinse the tail light. 8) After cleaning is done ,apply a plastic material polish cream on the tail light and gently rub it till the tail lights shine. This will help.thanks.
Read full tip
on Mar 18, 2010 • BMW 528 Cars & Trucks
0helpful
1answer

Rear turn signal b ulb burned out - How to replace
Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif
Read full answer
Dec 19, 2010 • 1994 Buick Century
0helpful
1answer

Replace a brake light
COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Read full answer
Nov 04, 2010 • 1998 Saturn SL
0helpful
1answer

I need to replace rear tail light bulbs on 1996 Saturn SL1
COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif
Read full answer
Oct 23, 2010 • 1996 Saturn SL
2helpful
2answers

How do I replace a burned out backup light on a 1998 cheverolet silverado c-1500 pickup truck?
Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif
Read full answer
Jul 17, 2010 • 1998 Chevrolet C1500
1helpful
1answer

How do you remove the tail light asy.to replace the brake light bulb on a 2000 sable wagon. Thank you, any help will be great. Charles.
Hi Charles,
this is an easy one for you,
open your trunk and pull carpet away from where the tail light is on the one you want out,you will see five plastic thumb nuts,you just remove them and pull the lens assembly out,remove the bulb you want to change by turning it counter clock wise.
Read full answer
Jan 01, 2010 • 1998 Mercury Sable
0helpful
1answer

How doI turn off the oil light on a 528 2005 bmw
needs to be put on computer to turn off fault light
Read full answer
Nov 23, 2009 • 2008 BMW 528i Sedan
1helpful
1answer

Replace left tail light assembly on 2003 325i- have replacement lens, but not sure how to remove old cracked lens and install replacement
If you pull back the carpet in the trunk directley behind the lens, you should find the mounting screws. Some models only need to have a few plastic wing nuts removed without pulling back the carpet.
Read full answer
Oct 26, 2009 • 2003 BMW 325
0helpful
1answer

Tail lights
behind paneling in trunk or whole tail light assembly come off. There is no seperate lens.
Read full answer
Jun 16, 2009 • 2000 Ford Focus
Not finding what you are looking for?

View Most Popular

2007 328xi Sports Wagon

  • Cars & Trucks

Related Question

How to remove tail light lens on 2000 ford contour SE

  • 2000 Ford Contour

65 views

Ask a Question

Usually answered in minutes!

Popular Questions

BMW 328i Starter how to replaice

1999 BMW 328 Series

E36 BMW convertible top operating it manually

1997 BMW 328

How can i get bmw 323i convertible top down manualy

1997 BMW 328

Check Engine Light on - codes P1423 P1421

1997 BMW 328

328i BMW, and the EML light is on

1999 BMW 328 Series

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top BMW Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

old marine
old marine

Level 3 Expert

2426 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2007 328xi Sports Wagon Manual

2007 328xi Sports...

Loading...