1992 Chevrolet C1500 Logo

Related Topics:

A
Anonymous Posted on Dec 06, 2012

92 chevy c1500 heater control panel only works fan on high no med.or low??

5 Related Answers

Rick Gillis

  • 37 Answers
  • Posted on Dec 06, 2008

SOURCE: Heater only work on high

Most likely is the resistor when they fault the default to high giving you off and high only

Ad

Anonymous

  • 3 Answers
  • Posted on Feb 15, 2009

SOURCE: a/c heater climat control switch

Check the relais module located inside under the rh side of the heather box you can see the connector most of them need to be replaced as they burn out you may need to replace the blower motor as well,high amp draw caused by faulty bearings will overload the blower motor controller

Anonymous

  • 75 Answers
  • Posted on Apr 01, 2009

SOURCE: 1993 Chevy Silverado truck headlights high beam only works no low

dimmer switch has gone bad need to change your dimmerswitch

Anonymous

  • 82 Answers
  • Posted on May 05, 2009

SOURCE: Need a diagram for a

the low side should have a blue cap on the service port and the high should have a red cap, also the high side port is larger than the low side. hope this helps

david dixon

  • 740 Answers
  • Posted on Jan 06, 2010

SOURCE: 1997 Chevy S10 pickup Fan switch for heater runs on high only.

replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

1992 chevy C1500: Heat works on low speed, no medium, and high only works intermittantly.

On any other vehicle it sounds like the blower fan switch.
The fan switch provides power or ground to the resistor and there would be a high speed blower relay to bypass the resistor.
But in your case the fan switch is part of the controller.
I don't have a diagram for a 92 but the 94 model shows relays for low medium and high speeds. Each relay gets power from a fuseable link. The high relay gets power thru the low relay if the low relay is not engaged.
If you have the model with 3 relays you may need to check them.
3helpful
1answer

Blower Controls No Low or Med Just High Speed

problem could be in blower motor resistor or blower motor control switch is bad.
0helpful
1answer

Why does my heater in my 2000 ford ranger only work on the high setting?

I assume that you are talking about the heater fan?

Your heater FAN has at least 3 settings, and for our purposes we will assume low,med and high

Low and medium run through a resistor High is wired direct
Either your resistor is bad or your fan is
I know it seems wrong that the fan could be shot but it could be pulling so many amps that it won't work in any other mode than high
I just had this happen on one of my trucks
Start with the fan
0helpful
1answer

My heater won't blow out any air unless it is on high with the fan blowing.

Hello let me verify.
1 heater wont blow out warm air unless on high?
possible clogged airfilter.low on coolant or antifreeze.

2 heater wont blow any air unless on high?
Could be a bad switch low ane med do not work.
Not finding what you are looking for?

492 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...