Passenger side and rear windows and locks not working

You say the driver window works? wouldn't be a main fuse or fusible link then -driver door locks and window wouldn't work either. Each door has a module inside (computer) . The driver door has a circuit breaker power feed an a fuse DDM fuse 10amp located in rear junction block circuit breaker is located in under hood maxi fuse block. The circuit breaker also feeds battery voltage to the other door modules too. PDM - passenger door module fuse 10amp located in the instrument panel fuse box and the RDM - rear door module RDM fuse 10amp located in the rear fuse box - under the back seat.

Each power window is connected to a permanent magnet motor. The motor raises or lowers the glass when the door module applies voltage to the motor. The direction the motor turns depends on the polarity of the supply voltage provided by the associated door module. The 2 front doors have their own separate modules. The rear seat contains a single module, which controls both of the rear power windows.
A serial digital communications link, called the simple bus interface, is used for communications between door modules and the driver's door power window switches. The use of serial digital communications allows the use of a single wire to convey switching information between the power door lock switch and the driver's door module (DDM). The serial communication is also used in order to transmit switching information from the DDM to the other 2 door modules.
The door modules apply battery voltage of the correct polarity to the respective window motor when any local, or power door lock switch, UP switch is operated, driving the window up. Battery voltage is applied to the respective window motor in the opposite polarity when any local, or power window switch, DOWN switch is operated, driving the window down.

Driver Door Module (DDM)
The driver's door module (DDM) directly controls the driver's door window motor and the express down window feature. The DDM sends window UP/DOWN messages received from the power door lock switch to the passenger door module (PDM) and to the rear door module (RDM) over the simple bus interface (SBI) line. The DDM also contains a class 2 data link which communicates with the other vehicle system modules. The left front power door locks and the outside power mirror are also controlled through the DDM.
Passenger Door Module (PDM)
The passenger door module (PDM) controls the passenger's door window motor. The PDM controls the passenger's door window directly from the right front power window switch or from instructions over the simple bus interface (SBI). The right front power door locks and the outside power mirror are also controlled through this module.
Rear Door Module (RDM)
The rear door module (RDM) controls both of the rear door window motors. The RDM controls the rear windows directly from the rear door window switches or from instructions over the simple bus interface (SBI).

If you want to solve your problem, click on the link I attach-

https://www.reliable-store.com/products/2012-honda-accord-tourer-workshop-repair-service-manual-pdf-download

Check the window lock out. You may have pushed that on accident. It locks the passenger and rear windows so people dont use them when the driver wants to control window operation.. Usually for annoying kids :) The window lock out usually has a pic of a window with an "X" or a pic of a window with the word "lock"

If that is not it, It sounds like the controls went bad. This happens from time to time. When liquids get onto the window controls its common that some go out and or they all go out. I would put my best guess on the window lock out.
Only true and accurate way to check is manually see if power is exiting the window controller to the rear windows and or passenger window... you would need a Volt meter to watch voltage.

The windows and power locks are controlled through a central computer module called the Generic electronic module, you must have this module scanned by the dealer (or a well equipped shop with a Ford compatible scanner) to see what is wrong with the system.

The first thing to do would be to hook up a factory or professional type scan tool an check for DTC'S - diagnostic trouble code's . This vehicle has very complex electronic's. Serial data communication network,class2 data bus . There are electronic modules inside the door's that control the lock's ,power window's , power mirror's . Your best bet ,take it to a qualified repair shop . Not a fuse problem , driver an passenger door module each have thier own power supply. Two circuit breakers ,PWR/WDO circuit breaker 30 amp. You could check DRVMDL 10amp fuse ,located in the rear fuse box , PASSMDL 10amp fuse rear fuse box , RRDR/MDL 10 amp fuse rear fuse box . Rear fuse box is under the back seat . None of the window's , lock's etc.. work from any door switch ?

Do you know anything about automotive electronic's ? Serial data Communication network ? Electronic module's inside the vehicle doors , communicate commands ! No relay ,no fuse .
If the passenger mirror is selected and a direction switch is activated, the DDM sends a serial data message to the PDS indicating that the passenger mirror was selected and the direction to be commanded. The PDS will then supply battery voltage and ground to the appropriate control circuits for the direction selected.
DDM - driver's door module

Door Lock System Components
The power door lock system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of the rear doors.
• Door unlock relay--Located in the I/P fuse block and controls the unlocking of the rear doors
• Body control module (BCM)
• IP BEC
• Reversible door lock actuators in each door

Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Body control module (BCM)
• Passenger door module (PDM)
• Rear door power window switches
• Power window motors in each of the doors (circuit breaker protected)

Your best bet , take it to a qualified repair shop that has a diagnostic scanner that can pull code's an view input data form these systems . There is one circuit breaker for the window's an fuse's for the lock's . I would think a data network problem . But that would be a guess , without testing anything is possible on these .

My mechanic took out the panel on the driver side control because my right rear passenger window would not work after disconnecting the battery (but the control on the passenger rear door works) and when he put it back, it worked..it's possible it's just a loose wiring connection. My car is a 2006 Lexus RX330 with 58K miles on it.

I just bought a 2007 accord and its having the same problem. Was there any resolution?

This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action

• All windows are inoperative

• BJB Fuse:
  • F20.
• Circuit.
• Power window relay.
• Front door power window switch.

• GO to Pinpoint Test A .

• Single power window is inoperative

• Front door power window switch.
• Front door power window regulator.
• Circuit.
• Driver door power window switch.

• GO to Pinpoint Test B .

• Vent power window is inoperative — quarter window glass power latch

• Circuit.
• Quarter window glass switch.
• Quarter window glass power latch.

• GO to Pinpoint Test C .

• The one touch down feature is inoperative

• Master window regulator and door lock switch.

• INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .

• The back window will not defrost

• CJB Fuses:
  • F30 (10A).
  • F32 (20A).
  • F34 (20A).
• BJB Fuse:
  • F27 (45A)
• Circuit.
• Heated back window switch.
• SEC/timer module.
• Rear window defrost relay.

• GO to Pinpoint Test D .

• The back window defrost will not shut off automatically

• SEC/timer module.
• Circuit.
• Rear window defrost relay.

• GO to Pinpoint Test E .