The traction control light in these years is usually a bad wheel speed sensor built into the wheel bearing. Cost around $600. The audio may be as simple as entering the unlock code. The deceleration could be a hundred different things so you'll have to pay to get that diagnosed.
STARTING DISABLED REMOVE KEY
Refer to Theft Systems Description and Operation in Theft Deterrent
STARTING DISABLED REMOVE KEY
The radio illuminates the STARTING DISABLED REMOVE KEY message when the VTD system has disabled the starting system. The radio receives a message from the theft deterrent control module via the serial data circuit requesting illumination.
Your best bet ,take it to Cadillac dealer and have it checked . Could have DTC'S - diagnostic trouble codes
DTC B1015
DTC B1016
DTC B3031
DTC B3055
DTC B3060
DTC B3090
DTC B3935
DTC B3976
DTC P1629
DTC P1630
DTC P1631
The theft deterrent module or the insturment cluster or the ECM is not seeing correct info.
The vehicle theft deterrent (VTD) system functions are provided by the theft deterrent control module. When an ignition key is inserted into the ignition lock cylinder and the ignition is switched ON, the transponder embedded in the head of the key is energized by the exciter coils surrounding the ignition lock cylinder. The energized transponder transmits a signal that contains its unique value, which is received by the theft deterrent control module. The theft deterrent control module then compares this value to a value stored in memory, learned key code. If the value is correct the theft deterrent control module sends a random generated number to the transponder, this is called a challenge. Both the transponder and the theft deterrent control module perform a calculation on the challenge, if the calculations match the theft deterrent control module sends the fuel continue password via the serial data circuit to the Engine control module (ECM). If either the transponders unique value or the calculation to the challenge is incorrect the theft deterrent control module will send the fuel disable password to the ECM via the serial data circuit. The components of the VTD system are as follows:
• Theft deterrent control module
• Engine control module (ECM)
• Ignition key (Transponder)
• Ignition lock cylinder
• Security indicator
If you REALLY want help, you need to do what you would have to do at ANY auto parts store. The first question is ALWAYS "What are you working on?" Without having to be ASKED, you should ALWAYS VOLUNTEER the following info:
MAKE
MODEL
YEAR
TRIM (seires)
ENGINE
TRANSMISSION
If you pull the windows they will separate from the window channel hardware. If separated there is nothing to keep the window glass held up and it will fall back down. Check your fuses for power windows, there may be more than one. Also check the power window relay(s). The relays may be located under the hood in the fuse box.
Your dts uses drive by wire. The gas pedal is actually an electrical switch connected to the engine computer which then actuate a throttle body motor which causes the car to speed up or slow down. If you mean the car won't acceleration then the throttle actuator is probably going out, this is common and you replace the throttle body assembly as the actuator is sealed onto it. Had the same problem with my 04 srx (which is mechanically the same as a cts). If you have a check engine light on (and you should) get the codes read first as there are a few other problems that can cause throttle problems, however they are less likely the cause.
It could be that your vehicle is engaging the "safe mode" upon restarting. Auto Zone and Advance Auto will perform a complimentary diagnostic check which will most likely identify the issue. The trouble codes are stored and may be retrieved even when your car is running okay.
Is the motor receiving power? If not you have to check electrical system to locate the place that is not transmitting power. Could be a fuse/relay, switch, bad connection.
If the motor is turning and nothing happens then the drive mechanism from motor to sunroof is stripped. Not good.
You mean P0202 , an what engine does yours have ? 2.6 L ,3.3 L , 3.6 L or 5.7 L ?
DTC P0201, P0202, P0203, P0204, P0205, or P0206
The engine control module (ECM) enables the appropriate fuel injector on the intake stroke for each cylinder. Ignition voltage is supplied directly to the fuel injectors. The ECM controls each fuel injector by grounding the control circuit via a solid state device called a driver. The ECM monitors the status of each driver. If the ECM detects an incorrect voltage for the commanded state of the driver, a fuel injector control DTC sets.
Test your fuel injector for cylinder #3 ! Do you know how to do that ?
You probably changed computers for nothing ! Check out this video on testing fuel injector circuits an checking computer driver that controls the injectors , Oh , by the way P0300 P0301 an P0302 are misfire codes , P0300 is a random misfire an the other two are for cylinders 1&2
Testing Fuel Injectors FastPCM Driver Testing II without scan tool Did you just replace the PCM - engine computer ? Didn't test anything !