1993 Dodge Dynasty - Answered Questions & Fixed issues
1993 Dodge Dynasty. Wipers stopped working.
BCM's are part number specific to your particular vehicle so unless you got from a dealer and had the dealer flash it for you none will work.
Caravan's had the same problem with their bcm's
Did you test the motor to see if it was working before you got the bcm's?
Did you test the wiper motor switch?
Also test the wiper motor relay.
8/30/2016 3:34:17 PM •
1993 Dodge...
•
Answered
on Aug 30, 2016
•
460 views
Windshield wipers won't work
does the motor still run if it does the arm that moves the blades have come loose if not check fuse relay or the motor itself.
8/30/2016 3:32:17 PM •
1993 Dodge...
•
Answered
on Aug 30, 2016
•
611 views
How do I change the turn signal bulb on my 1993 dodge dynasty
Front or rear? If its the rear light, you should check inside your trunk. Move any liner that may be over the light housings, and look for fasteners, usually plastic wing nut types, that you can remove and lift out the whole tail light assembly. Once out, you can change the individual bulbs.
If it's the front turn signal, I think that's part of the headlight assembly, and you may have to remove the whole assembly to get at the bulbs. Look for screws in the top cross member, and in the panel next to the radiator to remove the assembly.
1/23/2016 3:18:00 AM •
1993 Dodge...
•
Answered
on Jan 23, 2016
•
434 views
Where is the darn turn signal relay on my 93 Dodge Dynasty??
You will need to remove the glove box/ash tray section of the lower dash.It comes out as one piece.Once removed, the block containing the flasher and relay are above the fuse block towards the center partof the dash.Heck of a place for it!!!!!!!!!!!!!
4/23/2015 1:51:30 AM •
1993 Dodge...
•
Answered
on Apr 23, 2015
•
1,032 views
93 dodge dynasty steering issues
Hey Laurie. It may be that the right brake caliper is running tight and when it heats up it will bind, like applying the brakes to the right front only. Does it straighten out when you hit the brakes? If so, that is most likely the problem. Tommy
9/6/2014 3:06:20 PM •
1993 Dodge...
•
Answered
on Sep 06, 2014
•
115 views
1993 dodge dinesty 3.4 fuel rail leaks how can i repair
If the metal fuel rail itself has a leak, it should be replaced. If it is leaking by an injector, the O-rings on the injectors need to be checked and probably replaced. If a fuel line to the rail is leaking, that will have to be repaired. There will be two fuel lines at the rail, the feed line in from the gas tank, and a return line from the rail back to the tank. If there is a pressure regulator on the fuel rail (it will have a short vacuum line hose to it), the regulator may also have an o-ring to keep from leaking where it mounts.
5/25/2014 8:37:21 PM •
1993 Dodge...
•
Answered
on May 25, 2014
•
371 views
Speedometer
speed sender is no workee no more
10/18/2013 10:22:43 AM •
1993 Dodge...
•
Answered
on Oct 18, 2013
•
297 views
Change ignition switch
There are lock pins or smap rings you have to locate them and speciality tools will be needed.
10/14/2013 8:59:05 PM •
1993 Dodge...
•
Answered
on Oct 14, 2013
•
38 views
Trouble codes 12 then 55
Well those are codes, but not trouble codes.Code 12 is the start and also means there are no codes since the battery was disconnected, and 55 is the end of the test.
5/31/2013 8:50:15 PM •
1993 Dodge...
•
Answered
on May 31, 2013
•
156 views
Diagram
Have the fault codes read. Replace faulty items. Use onlygenuine items as replacement as non-genuine are not always compatible with the OEM fitted CPU units. This results in the fault codes not cancelling out.
5/26/2013 7:25:32 AM •
1993 Dodge...
•
Answered
on May 26, 2013
•
81 views
Car just stops hard to restart
Check fuel pressure at motorRun some tests on fuel pumpFuel pressure,volume,current or scope it& check armature pattern for failing pump
2/12/2013 12:30:51 AM •
1993 Dodge...
•
Answered
on Feb 12, 2013
•
118 views
Not finding what you are looking for?