Re: Trying to take apart the lemax spooky town witches...
I tried, it looks like its still connected under the two witches that move. Mine got stuck and the witch don't move any more, but i see 2 may be 3 screws under the pot with the skeleton.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You can try to find drive belts for Lemax products in the following places:
1. Lemax Official Website: Check if Lemax sells replacement parts, including drive belts, on their official website.
2. Local Retailers: Visit hobby shops, Christmas stores, or stores that carry Lemax products. They may have replacement parts or can guide you to a source.
3. Online Marketplaces: Websites like Amazon, eBay, or specialized hobbyist forums may have listings for Lemax replacement parts, including drive belts.
4. Lemax Collector Groups: Join online Lemax collector communities or forums where enthusiasts share information about where to find replacement parts.
5. Contact Lemax Customer Support: Reach out to Lemax's customer support for guidance on where to purchase replacement drive belts.
Remember to provide the specific model or product details to ensure you get the right drive belt for your Lemax item.
This advice is for Kenmore Elite, Whirlpool Duet and Maytag Epic model FRONT LOADING washing machines.If you experience a problem where the washer does not drain properly or the drain pump makes excessive noise, here’s the information you need to check the drain pump:
Unplug the washer while servicing inside the unit.
Remove the lower kick panel under the door by removing the three 7mm screws under the bottom edge of the panel.HINT: Use a couple of blocks of wood to prop up the front feet of the washer to gain better access to the screws.Once the screws are removed the panel should drop down, and then pull off.If the panel becomes stuck, a slight tap on either side will dislodge it.
Locate the drain pump.It will be located directly under the wash tub (it is the only pump this washer has).
There is an access removal cover on the pump that can be removed to clean out the trap.BEFORE doing this, it is strongly recommended that you remove all residual water from the wash tub & drain line or you will have about a gallon or so inside your washer and on the floor to clean up.
Here’s a helpful way of quickly removing the residual water.If you own a wet/dry shop vac, remove the drain hose from the standpipe at the wall and pull a vacuum with the shop vac.This will empty the wash tub, pump and drain lines.If you don’t own a shop vac, grab a bunch of old towels and open the access on the pump slowly so that it comes out at a trickle.Allow the towels to soak up the majority of the water.Close the access and stop the water if you need to get additional towels.
Open the pump access and remove once you have all the water drained.Check the drain pump for foreign objects and debris.Check the pump impeller and make sure there’s nothing caught in it.Items as small as toothpicks or cotton swabs have been known to stop this pump from working.
Clean out the pump thoroughly and reinstall the access cover.Make sure the cover is snug, but do not over tighten.
Place the drain hose back in the standpipe (IMPORTANT – DO NOT FORGET!).
With the bottom panel still off, plug the washer back in and select the following on the operator console – DRAIN SPIN, NO SPIN, and then press any button under OPTIONS 4 times (it must be the same button).“C00” will show on the console display as the washer begins diagnostics mode.
Check the drain pump for leaks as the washer fills.The pump is gravity filled and will hold water even it is not pumping.Allow washer to run through diagnostics until it begins the wash tub tumble cycle.
At this point, you can stop the diagnostics procedure by pressing PAUSE/CANCEL 2 times.The drain pump energizes and the washer will begin to drain.
If the drain pump works normal and there are no leaks detected, reinstall the bottom panel and tighten screws.
NOTE: It is normal to have residual water left inside the wash tub under the wash basket.This is why it is important to leave the door ajar when not in use so this water does not become sour.
There are more than 90% models of the PC accessories and batteries of the market you can find in this website, for more information, please visit :www.ukbatterystore.com
×