At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I have 1994 yamaha 200 H.P Jet, I run NGK BR9HS and it calls for gap at .058 - .063...I have 1994 yamaha 200 H.P Jet, I run NGK BR9HS and it calls for gap at .058 - .063...
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
A common problem with an easy solution, Yamaha boat engine
trouble could arise due to inadequate levels of fuel or engine oil. All
Yamaha outboards take unleaded gasoline as a main fuel source with a
pump octane rating of 86 or higher. The type of engine oil varies
according to motor size and can be found in the "Specifications" section
of a particular outboard's owner's manual (See Resources).
Electrical
Problems with the electrical system can also prevent a
Yamaha outboard's engine from working correctly. Troubleshoot the
electrical system, first removing the main fuse that's located
underneath the electrical panel on any electric-starting outboard. If
the connection at the center of the fuse is broken, it must be replaced
by a fuse of the same amperage. The battery should also be removed,
cleaned and fully charged when troubleshooting the electrical system.
Spark Plugs
Owners should also remove and inspect the spark plugs during
the troubleshooting process. If the insulator tip of any plug is
burned, that spark plug should be replaced. The number and type of spark
plug depends on the specific outboard. Additionally, owners should
ensure that each spark plug gap is set to the width stipulated in the
owner's manual (see Resources).
is you propeller bent? a dent the size of a quarter will cause a shake. If not that means your engine is misfiring. here are the troubleshooting test and tool list you need to find out. Tools(1) A compression gauge (2) a spark gap tester.(3) A Clymer service manual for your engine. (you can purchase from your local outboard dealer. I know all these are expensive but if your going to be a outboard tech you will always need them. Troubleshooting (1) check compression. without the year model I'm giving you a average numbers. Look at your Clymer manual. all cylinders need to be over 100 lbs and equal each other within 5 lbs.(2) check spark. use a spark gap tester all cylinders should jump a half inch gap. if you have good compression and good spark, fuel is the problem nine times out of ten.Ethanol gas is proven to stay stable in fuel systems for 30 days in 90 + degree heat. Drain gas tank,clean fuel lines replace primer bulb and replace all fuel filters. Yamaha has a gravity filter under engine coul clean it. Finally replace spark plugs, I know spark plugs probably don't look bad but this is a outboard. Fresh spark plugs means less resistance for the ignition system. The ignition system is week compared to automotive. Test drive boat, if the problem is still there then there is further steps to take. Again I don't know the year model so I guessing its fuel injected. Pull out your clymer manual. what is great about the Clymer Manual for Novice techs is it gives detailed info on your outboard. Troubleshooting tips and teaches you how your outboard works.
need year and make? Tools(1) A compression gauge (2) a spark gap tester.(3) A Clymer service manual for your engine. (you can purchase from your local dealer). I know all these are expensive but if your going to be a outboard owner you will always need them. Troubleshooting (1) check compression. without the year and make I'm giving you a average numbers. Look at your Clymer manual for specific specs. all cylinders need to be over 100 lbs and equal each other within 5 lbs.(2) check spark. use a spark gap tester all cylinders should jump a half inch gap. if you have good compression and good spark, fuel is the problem nine times out of ten .Ethanol gas is proven to stay stable in fuel systems for only 30 days in 90 + degree heat. Drain gas tank,clean fuel lines replace primer bulb and replace all fuel filters. Yamaha has a gravity filter under engine cowl clean it. Finally replace spark plugs, I know spark plugs probably don't look bad but this is a outboard. Fresh spark plugs means less resistance for the ignition system. The ignition system is week compared to automotive. Test drive boat, if the problem is still there then there is further steps to take. Again I don't know the make so I guessing what fuel injected system. Pull out your clymer manual. what is great about the Clymer Manual for Novice techs is it gives detailed info on your outboard. Troubleshooting tips and teaches you how your outboard works. without the test information I would guess the electric fuel pump. but test everything first because a mercury efi fuel pump will set you back 600.00
Yamaha 150 HP outboard
I have 1994 yamaha 200 H.P Jet, I run NGK BR9HS and it calls for gap at .058 - .063...
×