Re: Change batteries on my toshiba se-r0001 remote
Locate the Battery Cover: Look for the battery cover on the back of the remote control. It is usually a small compartment that can be easily opened.
Remove the Battery Cover: Depending on the design, there may be a latch, screw, or sliding mechanism to secure the battery cover. Use your fingers or a small screwdriver to open the compartment.
Remove Old Batteries: Take out the old batteries from the battery compartment. Pay attention to the orientation of the batteries, so you know how to insert the new ones correctly.
Check Battery Polarity: Take note of the positive (+) and negative (-) signs inside the battery compartment. Make sure to insert the new batteries with the correct polarity to match these markings.
Insert New Batteries: Place the new batteries into the battery compartment, ensuring they are properly aligned with the correct polarity. Press them down gently to make sure they are secure.
Replace Battery Cover: After inserting the new batteries, close the battery compartment cover securely. If it has a latch or screw, make sure it is fastened properly.
Test the Remote: Point the remote at the device it controls (such as a Toshiba TV) and test whether it responds to your commands. If the remote is working correctly, you have successfully replaced the batteries.
Dispose of Old Batteries: If the old batteries are no longer usable, make sure to dispose of them properly. Many communities have designated recycling locations for batteries.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It had been working fine. Wired to modem, home computer working fine. It does a ...My remote SE-R0377 will not operate my BDX3200KY player. Im not sure if ...Missing: controller
www.fixya.com/support/t16019942-remort_se_r0398_not_working
Jan 20, 2013 - remort se-r0398 not working remote and buttons on blu-ray player not working model bdx1100kb - Toshiba SE-R0398 ... Question about Toshiba SE-R0398Remote Control AH802703 ... I need help with syncing my controller!
1) Reset the code again, if you do not have it go to www. fitness.manualsonline.com or www. remotecodelist.com
2) Change the new batteries, by allkalines 3) Clean the contacts batteries very well. 4) Resolder the wires connector contacts. 5) Open the remote control and clean the keypads with special spray contacts cleaner. radio schack.God bless you
.Make sure there are working batteries in the Toshiba remote control.
2.Turn on your television set, DVD player or other device that you want to control with the Toshiba remote.
3.Find the "Recall" or "Setup" button on
the Toshiba remote control. After you find it, press and hold down that
button until the lights on the remote control turn on and remain lit.
4.Point the Toshiba remote at the device you turned on in Step 2 and press the button on the remote for that device. 5.Begin pressing the "Power" button on the
Toshiba remote. Continue doing this until you have turned the device off
using the Toshiba remote. Once it shuts off, press "Enter" on the
Toshiba remote. The remote will then be programmed OK.
There isn't one. This is a dvd player remote. You will need to control the volume with either your tv remote or surround sound remote if you have surround sound
There is most likely nothing wrong with your remote. I just had exactly the same issue with my SE-R0161 remote. (I had just changed my remote batteries too and was getting a DR-2 code on the Toshiba DVR RD-XS52 unit's display.) My DVR and my remote had to be realigned so that they both have the same infared (IR) code. The remote and the DVR can have DR 1, DR 2 or DR 3 as remote codes. Pg 54 of the Toshiba Installation Manual explains how to align both your SE-R0161 and your based unit so that the remote works again. Good luck. Hope this helps.
×