I have a 1991 cr250 wont start it has compression ,spark and gas to carb?? feels like it wants to kick over.problem started with having gas going thru carb was flooding , completely cleaned carb now wont start, please help!!

fuel/spark /compression

Check fuses. Get a new spark plug then check for spark by hooking up the plug wire then hold the metal side of the plug against the cylinder. Have a friend kick the engine over while you look for spark. Remove the carb, then remove the float bowl from the bottom of the carb. Use spray carb cleaner to clean the carb. How old is the gas? Flush the tank and fill with fresh fuel if old gas is present. Please rate my answer. Thanks.

A rebuild kit on a 2004? Why was that needed?
I would do a compression test to verify that the ring, and valves are working for you. Should be above 100 psi. (Throttle open while kicking it over) This may help get you started toward a fix.

Install a new stock spark plug. Clean the air filter then remove and clean the carb. Drain the gas tank, clean out rust and any trash, and remove the fuel valve to clean the internal tank filters. Now install an in-line fuel filter in addition to the tank filter.
What follows is just in case it will help out. Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} There is a proper way to start the engine. Four controls are on your bike to assist in starting. Below are generic instructions.

• The choke, used when the engine is cold. Pull the red knob for choke.
• The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
• The de-compression lever, always used.
• The throttle, used to prime the cylinder, (power valve).

Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm, (Power valve), in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), for six kicks. After six kicks go ahead and twist the throttle again for a second priming. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting. Note that not all carbs have a power valve. When a power valve is not present you should crack the throttle open only 1/8 inch from closed on each kick.

buy some 'start ya barstard' or aero start and spray directly in to the carby and start it just gives it a bit extra

ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.

There is a proper way to start the engine. Four controls are on your bike to assist in starting.

• The choke, used when the engine is cold. Pull the red knob for choke.
• The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
• The de-compression lever, always used.
• The throttle, used to prime the cylinder.

Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Assuming you are using fresh gas. Check to see if gas is coming out of the line, if not blow back up into the tank and if that works there's dirt in the tank. Check the spark by removing the plug and kicking it over with the plug touching the engine, look for spark. If no spark, try a new plug, if still no spark, you have a stator problem. It wouldn't hurt to clean the air filter in any case. Good luck!

There is a proper way to start the engine. Four controls are on your bike to assist in starting.

• The choke, used when the engine is cold. Pull the red knob for choke.
• The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
• The de-compression lever, always used.
• The throttle, used to prime the cylinder.

Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. Give a strong kick through the full sweep of the kickstart lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from a backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Top rating for this answer? Thanks!

Several things can cause the problem. First, spring for a new spark plug. The stock plug is NGK CR8E. Now the plug is eliminated as a problem. Next, pull the slide out of the throat of the carb. Now remove the jet needle. Put the needle clip on the 4th notch, (this is the stock setting). Use only premium gas. Next, follow the starting instructions below.

There is a proper way to start the engine. Four controls are on your bike to assist in starting.

• The choke, used when the engine is cold. Pull the red knob for choke.
• The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
• The de-compression lever, always used.
• The throttle, used to prime the cylinder.

Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. Release the de-compression lever and give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from a backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery and clean air filter will also aid in starting.

This will likely tame the beast for you. Please rate this answer. Thanks!

im thinking if it has spark and getting gas and has compression, the bike will run. sometimes a "WEAK" coil will give a good spark, but under compresion its not enough to ignite the fuel. if thats not the case, take the air filter off and spray starting fluid into the carb and with NO CHOKE, give it full throttle and kick it over. if that dont do it try compression starting it, tow it for some distance if you have to. if that dont do it, then there must be something wrong with the carb. jets, fuel air adjustment. thats all i have. good luck.