Why i can not go to sit for configure DAP-1360

I THINK you are asking about a D-LINK dap-1360 range extender IF so see THIS YOUTUBE:
How to Configure Link DAP 1360 Wireless Range Extender

Be SURE to see this:
dap 1360 range extender Google Search

And this one too...

DAP 1360 Configure as repeater
NOT in English but lots in life is not... You can STILL see his setup steps clearly!

Anthony

This is the manual for this wireless access point from dlink.

http://www.dlink.com.br/sites/default/files/product_download/DAP-1360_A1_Manual_v1.00.pdf

The error message should not mention emulators, return it to where you bought it, as it sounds as if the firmware version is not correct.

VISIT the dlink website,you can get assistance with your query
http://support.dlink.com/emulators/wbr2310/lan.htm

You "bricked" it -- responsibly recycle this "dead" unit, and replace it.

Is this the router that is currently connected to your network, and also the router that is providing you with internet right now? what would you like to setup?

Hey, you're almost there. The connection between the no-wireless PC over ethernet to the DAP-1360 Repeater is fine. The reason it can't connect to your LAN or the internet, however, is that the repeater isn't actually repeating your Ofir network, it is instead creating it's own, completely isolated wireless network (Ofir_EXT).


The D-Link setup and documentation is confusing, and doesn't have proper instructions for the repeater setup.


Rerun the setup wizard, setup as a repeater, then select manual configuration method.


Now, enter the wireless network name of your the network you want to extend (in this case, Ofir). Then enter the same security and password etc. for Ofir in the following fields, just like you were connecting to Ofir from a smartphone or laptop.
Once that is finished, you should be up and running. If things worked, you should NOT see any new wireless network. There should be Ofir and just Ofir. Wireless repeaters work invisibly, you'll still connect to the same network like you always did, but now it will have much improved range thanks to the DAP-1360. The computer entherneted to it should be networked on the wireless LAN and have internet access after this as well.



Good luck, I hope my instructions were clear. Wifi networking is easy, it's understanding all the manufacturers less-than-intuitive software that makes it hard.

have you tried turning on and off the router and AP? it would scan again...it looks like you just need to recheck connections and powers...

You can download the latest version of the firmware you need below. Just determine if you have dap-1522 or dap-1522 rev.B.
The serial number, hardware version/revision information, MAC address and model number, will be located on a label on both the outer box, and on the adapter itself, usually attached to the bottom of the unit. Example picture on the bottom of this page.

latest dap-1522 firmware:
ftp://ftp.dlink.com/Multimedia/dap1522/Firmware/dap1522_firmware_141b.bin

latest dap-1522 revB firmware:
ftp://ftp.dlink.com/Wireless/dap1522_revB/Firmware/dap1522_revB_FW_203b.bin

Install instructions for the firmware are on page 41 in this pdf:
ftp://ftp.dlink.com/Multimedia/dap1522/Manual/dap1522_manual_130.zip

Here is a great setup video for it:
http://www.youtube.com/watch?v=lYJPGqtyFZU

You can download the latest version of the firmware you need below. Just determine if you have dap-1522 or dap-1522 rev.B.

The serial number, hardware version/revision information, MAC address and model number, will be located on a label on both the outer box, and on the adapter itself, usually attached to the bottom of the unit. See the example picture on the bottom of this page.

latest dap-1522 firmware:
ftp://ftp.dlink.com/Multimedia/dap1522/Firmware/dap1522_firmware_141b.bin

latest dap-1522 revB firmware:
ftp://ftp.dlink.com/Wireless/dap1522_revB/Firmware/dap1522_revB_FW_203b.bin

Install instructions for the firmware are on page 41 in this pdf:
ftp://ftp.dlink.com/Multimedia/dap1522/Manual/dap1522_manual_130.zip

Here is a great setup video for it:
http://www.youtube.com/watch?v=lYJPGqtyFZU

just make sure that you belong with in the same IP range.
default DAP-1360 IP is 192.168.0.50
username : admin password :
change your PC IP address to 192.168.0.xxx (e.g. 192.168.0.2)
from there you may choose wizard or manual configuration.
you may change your DAP-1360 IP add according to your network settings in the office and you must change you PC IP address with in the same range.