How to remove support for drum when shipped

Dryers don't need Shipping Bolts, only Washing Machines. The drum is supported at the back bearing and at the front by the drum rollers. A washing machine has a completely fluid, free moving drum to allow for uneven loading which is evened out during the spin.

https://www.google.com/search?q=shipping+bolts+for+Samsung+dryer+dv42h5200gp%2Fa3

..

Go to www.coolerhinges.co

Under bestsellers click on 4. cooler shield cooler hinge type I igloo pair. 14.99 plus 5.00 shipping. Lifetime warranty.

If you need 3 hinges click on 2. cooler shield cooler hinge type I igloo three pack. 21.99 plus 5.00 shipping. Lifetime warranty.

Phone 1-888-810-7283

Lift it up from the hole at the bottom and off of the shaft

From the ad below, it replaces old water with fresh. ------------------------------------------------------------------------- » HVACR» Air Conditioners» Evaporative Cooler Accessories Universal Cooler Cleaning SystemBrand: MastercoolModel: CM120ASKU: 47495

$74.13

3 Business Day Shipping $7.91
No Longer Available Mastercool CM120A Universal Cooler Cleaning SystemTotal Ratings: 0
Average Rating: 0
Review this item Product Information Item Cleaning System Function Timer-actuated, Automatically Removes Mineral-laden, Dirty Water every Six Hours and Replaces with Fresh Water, Reduces Scale Deposits and Leaves Pads Cleaner, Saves Up to 70 Percentage of the Water Weight 3.10

• Replacement Motors and Accessories

• Universal Cooler Accessories

• Cleaning System
• Save up to 70% of the water used in bleed-off cleaning systems.
• Timer-actuated drain system automatically removes mineral-laden, dirty water every six hours and replaces with fresh water.
• Reduces scale deposits and leaves pads cleaner.
• Uses: For residential size coolers only.

• Note: Limited availability.

Universal Cooler Cleaning System, Clean Machine Pump Cooler Flushing Device for Residential Size Coolers Only

if it is new you may need to remove the shipping rods that keep the drum secure for shipping look in the back there should be two of them if its not new I don;t know the answer

were the drum support brackets removed after purchase? you may need to open the front access panel and remove two brackets that support the drum during shipping. also at the rear are support screws that need to be removed

The main thing you need to do, is to remove the toner bottle assembly, drum unit and developer unit. There is a small black stopper you'll see once you pull out the toner bottle unit. Remove the stopper and the tray holding the bottle will slide out of the machine. The drum unit has a thumb latch on top of the unit and all you have to do is open the right side door, release the lever and remove the drum unit. DO NOT TOUCH THE DRUM! The developer unit is below the drum unit. There is one screw holding a silver piece of metal which secures the unit in place. Loose the screw and fold it down to the left and then remove the developer unit. These steps will keep toner and developer from spilling out into the machine. Good luck.

HP Color LaserJet 2820 and 2840 AiO Series Products - How to Replace the Imaging Drum Replace the imaging drum

1. Push the scanner-release button to open the scanner assembly. Figure 1: Example of scanner release button location
2. Open the top cover. Figure 2: Example of top cover being opened
3. Grasp the imaging drum handle, and then rotate the drum until the handle is at the top.
   NOTE: The drum may be a snug fit. If needed, gently apply some force while rotating and removing the drum. Figure 3: Example of imaging drum rotation
4. Lift the imaging drum straight up to remove it from the device. Figure 4: Example of imaging drum removal
5. Remove the new imaging drum from its packaging.
6. Place the imaging drum on a firm surface, and then pull the orange rings to remove the shipping pins. Figure 5: Example of shipping pin locations
7. Remove the orange shipping lock on each end of the imaging drum, and remove the two orange shipping spacers. Figure 6: Example of shipping lock and spacer locations
8. Remove the orange cover from the imaging drum. Figure 7: Example of orange cover location CAUTION: Do not touch the surface of the roller or expose the roller to light for an extended period of time. Doing so could cause print-quality issues.
9. Align the arrows on the side of the imaging drum with the arrows inside the printer. Figure 8: Example of arrow location
10. Lower the imaging drum into the printer, and then press it firmly into place. Figure 9: Example of imaging drum installation
11. Close the top cover and the scanner assembly.

If you call (Cuisinart’s service center (800) 726-0190), they will send you a brand new unit for $10.00.
Happy Holidays,
AC Freeborn

There is a product call LITKIT TM, it is a universal shipping kit for washing machines. www.litco.com