Whirlpool Duet Sport ~ E28 Error Code

Display shows F20 or FH - Front-load washer ' Whirlpool ...

https://www.whirlpool.com/...fh-front-load-...

Whirlpool Home AppliancesQuestion: Display shows F20 or FH - Front-load washer. Answer. Image. or. Image. or. Image. This error code indicates a water supply problem. Are both the hot ...

whirlpool duet error code FH - Appliance Repair Forum

forum.appliancepartspros.com > Appliance Repair Help > Washer Repair

Jan 5, 2009 - 10 posts - ‎1 author
... Repair Help > Washer Repair » whirlpool duet error code FH .... FH No water detected entering machine or Pressure switch trip not detected. Whirlpool Duet diagnostic code C:03 error code FH
1 post
Dec 5, 2014
Whirlpool Duet Washer HF Error Code
3 posts
Jun 10, 2013
FH Error Code on Whirlpool Duet Washer
2 posts
Mar 11, 2013
FH error code
9 posts
Sep 13, 2008
More results from forum.appliancepartspros.com

Stumped on error code FH for Whirlpool Duet front load washer .

The following list of codes indicates an electronics communication problem with the washer: - Duet HT washer - F01, F03, F06, F11, F23, F24, F27, F28, F29, F30, F31, F32, F35, F42, F61, F62, F63, F64, F65, F70, F71, and F99

If Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, call for service.

I would first replace the door latch/lock assembly, a number of users have and it fixed the F-11 error code completely. Its the cheapest part for this problem.

Hope helps.

That's a door unlock error. The machine will display that code when after trying 6 times to unlock the door, it still won't unlock.

power failure--------unplug the unit for 5 minutes and see if it clears that code

Go to the Whirlpool webside and download a manual for free. They are good folks.

Here is mine...

https://secured.whirlpool.com/Service/.../Duet%20Job%20Aid.pdf

G.

check your manual. it will tell you what it means and what to do

F/02 Long Drain
If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed.
NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

Press PAUSE/CANCEL twice to clear the display.

• Check the drain hose and make sure it is not plugged or kinked.
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects.
• If the above does not correct the problem, replace the pump

Motor Control Unit (MCU)
Heat Sink Thermal Trip
If the thermal protector on the MCU heat sink gets too hot, it will open
the thermal protector on the heat sink which will stop motor functions
and an “F/10” will be displayed.
1. Check for proper installation, verify the unit is not located
near a source of heat and has proper ventilation.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the MCU, the motor,
and Central Control Unit (CCU).
4. Check the drive system for any worn or failed components.
5. Plug in washer or reconnect power.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.

Is there an sd error displaying? What you need to do is press pause/cancel two times to clear the display

F23 codes indicates an electronics communication problem with the washerThe following list of codes indicates an electronics communication problem with the washer. To remove the error display, press Pause/Cancel twice.
If Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, then call for service