Register handset to base unit on sn-920 - EnGenius Lands Phones

Register SynJ SB67108 Handset
How to register AT&T Synj SB67108 to new base unit SB67138?

To register an AT&T SynJ SB67108 handset to a new SB67138 base unit, you will need to follow these steps:

1. Make sure the new base unit is plugged in and turned on.
2. Press and hold the "Menu" button on the handset until the display shows "Menu."
3. Use the navigation buttons to select "Registration" and press "Select."
4. Select "Base" and press "Select."
5. The handset will begin searching for the new base unit.
6. Once the base unit is found, it will be displayed on the handset's screen.
7. Select the new base unit and press "Select" to complete the registration process.
8. The handset should now be registered with the new base unit.

Note: if you have multiple handset you need to register, repeat step 2-7 with each handset.

This is the registration procedure

Step 1: press MENU-6 and select 3 “SET BASE”
Step 2: press the REG key on the master base
Step3: press register to finish the registration procedure.
• After the registration complete, handset 11 and handset 21 can
2-WAY intercom with each other

If issue persists reset the unit start registration by using 2nd unit that currently unable to register. if issue continues please inform for further troubleshooting

Good Luck

Please use the below link to assist you with handset registration.

http://service.us.panasonic.com/OPERMANPDF/KXTG5621S.PDF#page=35

335 is the magic code when you want to remove a previous handset or base station registration!
Handset:

1 " (middle soft key) i L i #

2 Enter "335".

3 "Cancel Handset" i #

LThe numbers of all handsets

registered to the base unit are

displayed.

4 Select the handset(s) you want to

cancel, by pressing the desired handset

number. i #
5 "Yes" i # i {ih}
Base Station:

A handset can be registered to a maximum

of 4 base units. A handset can cancel a base

unit that it is registered to. This allows the

handset to "forget" the base unit.

1 " (middle soft key) i N i #

2 "Registration" i #

3 Enter "335".

4 "Cancel Base" i #

5 Select the base unit(s) you want to

cancel, by pressing the desired base unit

number. i #
6 "Yes" i # i {ih}

First make to get a compatible handset.

For the Uniden D1660-2, the compatible handsets are DCX160 and DWX337. Make sure that you have not exceeded the number of handsets that the phone can support. The D1660-2 can support 12 handsets unless you use any DWX337 handsets. Then the limit is 6. (If you have more handsets, you will need to deregister some of them first.) Then allow the handset to charge. If the handset is reading "not registered", then place it into the base unit. You should see "Handset Registering" for about 30 seconds; then it will read Registration Complete. The manual for the Uniden D1660-2 is available here: http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/D1660-2om.pdf . This is the most common Registration for Uniden phones; there are a few exceptions (depending on the base or the replacement handset). Check the appropriate manual (see below to find the manuals).

For the DECT4096, press Menu on the base and then navigate to Handset Register. When you see Handset Registering on the base display, press and hold # on the handset to be registered until you see Handset Registering. (It takes about 2 seconds.) After the display changes to Handset Registered, check for dial tone.

On a few Uniden phones, there is a Page/Handst Register button on the base. On those you navigate through the Handset menu to Handset Register (Menu > Handset menu > Handset Registration). Then press and hold the Page button until you hear a beep. Then wait for the registration to be completed.

Most Uniden manuals are available here: http://www.uniden.com/scat/cordlessphones_mnl . Select your type of Uniden phone and scroll through the list to your model or use the search box to directly search for your phone and the manual.

I hope this helps.

Cindy Wells

Registering a unit Operating additional
handsets
Additional handsets
Up to 6 handsets can be registered to
the base unit.
Important:
L See page 6 for information on the
available model.
Registering a handset to a
base unit
The supplied handset and base unit are
pre-registered. If for some reason the
handset is not registered to the base
unit, register the handset.
1
Handset:
{MENU} i {#}{1}{3}{0}
2
Base unit:
Press and hold {LOCATOR} for 4
seconds until the registration tone
sounds.
L If all registered handsets start
ringing, press the same button to
stop. Then repeat this step.
L The next step should be
completed within 90 seconds.
3
Handset:
Press {OK}, then wait until a long
beep sounds.
4
{OFF}
Note:
L While registering, "Base
registering" is displayed on all
registered handsets.
L When you purchase an additional
handset, refer to the additional
handset's installation manual for
registration.

Hi! This may cure your problem!
Re-registering the handset
If “No link to base. Move closer
to base, try again.” is displayed
even when the handset is near the base
unit, you may need to re-register the
handset to the base unit.
Important:
LMake sure the base unit is not being
used.
LHave the handset and base unit near
each other when re-registering the
handset.
LKX-TG5422 and KX-TG5423 only:
Confirm the extension number of the
handset which has lost its link to the
base by placing the handset on the base
unit or charger.
If you accidentally assign another
handset’s extension number to it, the
other extension will stop functioning.
1 Handset:
Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
3 Scroll to “Registration” by pressing
{V} or {^}, then press {>}.
4 KX-TG5421 base unit:
Press and hold {HANDSET
LOCATOR} until the CHARGE
indicator flashes.
KX-TG5422 base unit:
Press and hold the handset locator
button that corresponds to the handset
you want to re-register ({HANDSET
LOCATOR1} or {HANDSET
LOCATOR2}) until the CHARGE
indicator flashes.

Below is a link that will take you to the instruction manual for your phone.

http://www.phone-manuals.com/panasonic/KX-TG5422M.shtml

Hope this helps! Hal

Short answer:
No. This model of phone can only support 4 handsets. If you need more than that, you will need to have a second base unit.

Detailed answer:
One of my handsets went bad, and I just bought complete DCT748-4 package from a seller on eBay for a very good price. This set was used, but in very good condition. I didn't need the whole set - just one handset - but like I said, it was a good price. Anyway, I began by telling my old base unit to de-register handset #2 (the failed unit). However, I then found that I could not register the "new" handset with my old base unit because it was already registered to the "new" base unit. So, I first had to apply power to the "new" base unit and de-register the handsets. Then, I placed one of the "new" handsets onto my old base unit, and it said "Handset Registering ..." and registered just fine. Just for the fun of it, I placed one of the other spare handsets into my old base unit. It said "Hanset Registering ..." but then it beeped and said "Registration Failed." This is because I already had 4 handsets registered to my base, and the base can not handle a fifth handset.

. A new handset arrives with a handset ID number of 00, to register this handset to your system take the following steps:

1. On the EnGenius base unit press and hold down both the "Volume" & "Intercom" buttons for about five seconds. You will hear a beep from the base unit. You can now release the two buttons.
2. On the EnGenius handset (00), press the following buttons: "menu", "6", "1".
3. A new handset ID number (ie: 12, 13, 14…) is automatically assigned by the base and registration is complete.

hold the volume and intercom buttons together the in use light will come on and then go to menu on handset press 6 then 1 to regester that should work i just talked to a friend with a telecom buisness and he told me what to do with mine good luck