20 Most Recent
Saniflo SaniPlus-Round SaniPlus Macerator Toilet with Round Bowl - Page 7 Questions & Answers
When I flush my mascerating toilet, the tank
I assume you are referring to the holding tank and not the pump case.
The bowl float system on the couple SaniPlus toilets I have seen are similar to standard toilets. This will be a plastic float that slides up and down the water inlet tube. It will be attached to a shut off lever at the top of the tube by a metal rod. The float and rod are attached to each other by a "V" shaped clip. To adjust the shut off level you need to slide this clip up/down the rod.
If you remove the top of the tank and flush you should be able to see this working when flushing. Try shutting off the water flow by moving the shut off lever by hand. Use the water shut off at the inlet line leading into the tank to start and stop the water before it over flows if the lever does not work.
If the lever does not stop the flow then you have a problem with the water inlet mechanism and it may need to be replaced.
If your inlet mechanism is different from what I described please respond back with the model number of your SaniPlus.
Hope this helps.
6/22/2010 7:29:54 PM •
Saniflo...
•
Answered
on Jun 22, 2010
Hi i have a saniplus macerator unit hums but
sounds like an obstructed unit - you would need to remove the impeller cover at the base to check the pump - i'm assuming youve already checked the blade unit at the top (be careful here - i use a screwdriver - not my finger) could be that a simple cleanup and acid descale would be all thats needed. try this first then start looking deeper.Humming indicates motor is ok - but dont let it run continuosly - you dont want to burn out a good motor.
5/10/2010 9:04:01 AM •
Saniflo...
•
Answered
on May 10, 2010
My up flush toilet makes a humming sound every 5
Hi,
The pump has either gone bad or it is siezed up...you can try to unplug the pum and let it sit for a few hours then plug it back in... sometimes if you jog it on and off a few times you can get tiit to break loose and work again...if not you will have to take it out and replace the pump.
heatman101
5/4/2010 1:21:37 AM •
Saniflo...
•
Answered
on May 04, 2010
Sanipro xr massirato the problem is the pump is
You must remove the lid to gain access to the blades. Make sure you unplug the unit first. When reinstalling the lid place a little soap water around the gasket to help with the seal. thanks for using FIXYA. Jeff
4/7/2010 8:31:23 PM •
Saniflo...
•
Answered
on Apr 07, 2010
Pump cycles often
The following are the possible problems and
solutions:
- The tank flapper (Flush Valve) leaking allowing water into bowl. Make sure flapper is fully seated. If flapper is fully seated and still is leaking replace flapper.
- Faulty Non-Return Check Valve, water leaking back into Macerator. Clean and Inspect check valve replace if after clean water still flows back into Macerator.
I hope this answers your question and gives you a few more places to look. Please rate the answer on it's helpfulness. Good Luck and have a great day. Jeff
4/7/2010 8:27:31 PM •
Saniflo...
•
Answered
on Apr 07, 2010
Saniflo Saniplus pumps intermittently
If the discharge pipe runs vertically then the non-return valve is letting water drip back in to the tank and then it will self activate
2/26/2010 9:39:48 PM •
Saniflo...
•
Answered
on Feb 26, 2010
Saniflo Plus
Soak it in descaler and cold water for 24hrs then try again (may take 3-4 attempts) or remove pump/motor from the tank, find oval black rubber membrane, should be able to hear click of switch underneath when membrane is pressed, new membrane required if it is not flexable.
2/26/2010 9:14:39 PM •
Saniflo...
•
Answered
on Feb 26, 2010
Seems to be leakage out of the hole on the top of
If hole has a carbon filter in it then this is the air vent. If water is leaking from here then a known fault so contact nearest sani engineer (2yr warranty). Check water is not dripping down from above first!
2/26/2010 8:53:09 PM •
Saniflo...
•
Answered
on Feb 26, 2010
How do u open the pump to get in it
depending on how old it is....isolate power, remove discharge elbow, with flat head screwdriver GENTLY ease lid up and away from the securing lugs at each end. To refit... rubber seal fits to lid and using a rubber mallet gently hammer the lid back on to the tank.
2/26/2010 8:46:04 PM •
Saniflo...
•
Answered
on Feb 26, 2010
Is it okay to run a sink for a kitchenette through
It will be fine. The soap and hot water will keep the grease from congealing. Even if it does, the solids from the toilet and the rpm of the macerator will keep it pretty darn clean. I did one for a rental apartment 10 years ago and have no issues at all.
2/2/2010 4:15:51 AM •
Saniflo...
•
Answered
on Feb 02, 2010
Size of inlet for shower
Hi,
The inlet pipeworks for a shower to Saniflo would normally be 2" / 52mm polypipe as per the diagram (different saniflo unit type, but they are all the same)
If this helps please leave feedback, if not - let me know and I'll try and help some more!
1/27/2010 7:33:43 AM •
Saniflo...
•
Answered
on Jan 27, 2010
Not finding what you are looking for?