Top 20
Whirlpool Accubake RF362LXTT Electric Kitchen Range Questions & Answers
The Lock feature doesn't work (Whirlpool Accubake
Hi Stephen, that lock button locks the controls so settings can't be changed or oven started accidentally. Try putting the unit into self clean and see if that locks the door. If not it show an error code on the display telling you if there's a failed component. Give it try hopefully that will do the trick.
5/4/2017 8:42:05 AM •
Whirlpool...
•
122 views • 0 helpful votes
A code pops up on my oven e5 f2 what dose that mean
Hello Danny;
My name is Peter. I am a retired field service appliance technician.
F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
You have left the last number off your model number. If it is '0':
PART NUMBER: W10114377 Cost: $241.00
If you elect to replace the control board, make sure when you receive the new board in a anti-static gray bag, ground yourself by rubbing your hands on something that is bare steel. Static electricity will knock out a board.
The price provided is from Sears Direct. You can get the same part on E-bay for $110.00.
Rule of Thumb: "If the cost of repair is 1/3 or greater than the original purchase price, then buy new."
You have a older but nice unit.
Peter Goodwin
Glen Burnie, MD
443-306-1362
1/15/2015 2:27:28 AM •
Whirlpool...
•
1,301 views • 0 helpful votes
The code E5 F2 comes up on the control panel ,what dose that mean .
Hello Danny;
My name is Peter. I am a retired field service appliance technician.
F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
You have left the last number off your model number. If it is '0':
PART NUMBER:
W10114377 Cost: $241.00
If you elect to replace the control board, make sure when you receive the new board in a anti-static gray bag, ground yourself by rubbing your hands on something that is bare steel. Static electricity will knock out a board.
The price provided is from Sears Direct. You can get the same part on E-bay for $110.00.
Rule of Thumb: "If the cost of repair is 1/3 or greater than the original purchase price, then buy new."
You have a older but nice unit.
Peter Goodwin
Glen Burnie, MD
443-306-1362
1/15/2015 2:31:43 AM •
Whirlpool...
•
155 views • 0 helpful votes
Whirlpool accubake
Almost all electric stoves vent the oven through a hole in either the back right or rear burner. They can get very hot. I am surprised that your control panel is burned. It is only dangerous if you place a combustible over the burner. I have had some people do this and it has melted it. i haven'y heard of a fire from this but it could happen if it was hot enough.
7/31/2014 5:26:14 PM •
Whirlpool...
•
172 views • 0 helpful votes
Kenmore code F1 and broil wont go off
he clock on my STOVE started flashing F1
- You have either a bad ERC (clock) or a bad touch pad.
- Disconnect power to stove
- Gain access to the back of the clock (electronic range control or ERC).
- Unplug the touch pad ribbon connector from the ERC. This will be a flat wire apx. 1 1/2" to 2" wide.
- Make sure everything is clear and will not short out when power is turned back on.
- Turn power back on to stove.
- Watch for the F1 and listen for the beep.
- If you get the F1 and beep, replace the ERC.
- If after apx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.NOTE: Some models incorporate the touch pad and the clock as one part.
Here is the part to order.All parts come with a 365 day, any part, any reason return policy.
10/24/2013 3:56:42 PM •
Whirlpool...
•
164 views • 1 helpful votes
How do I turn off the lock on my electric oven
You may try starting a clean cycle again. This sometimes will run the lock motor to unlock the latch after it sets the lock. Cancel the clean after a few minutes. I hope this will help.
4/30/2013 2:40:04 PM •
Whirlpool...
•
123 views • 0 helpful votes
Cooktop light doesn't shut off
The temperature sensor located on the that element is failing. the sensor red light reminds you that the burner area is still hot. The light should go out once the glass top has cooled,but the failing sensor won't allow it. A slight rap with your hand on glass top over that burner once cool will put the light out. It more than likely continue until the unit is replaced.
1/20/2013 7:57:52 PM •
Whirlpool...
•
94 views • 0 helpful votes
Not finding what you are looking for?