Top 20 Samsung UN65ES8000 65" 3D 1080p LED-LCD TV - 16:9 - HDTV 1080p - 240 Questions & Answers

I urge you to update the firmware. (Verify the version to model match)file is available at http://www.samsung.com/ca/support/model/UN65ES8000FXZCThe only RISK is the TV should NOT reset/shutdown while performing this update.So it would be highly recommended to get the firmware update done at the Samsung service centre.

you will need to replace the leaky capacitors in the power supply circuit. You can locate the faulty capacitors with a visual check. Those that are bulging need to be replaced.

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.

i need the model,but the problem is in the T-con board.

Most likely the power supply capacitors. you can identify them by their bulging tops.

Hate to give you some bad news...But, It sounds like you have a bad screen. Samsung had several issues with the screens on this model. You may get lucky and may have a bad T-con board. The small board at the top center of the TV. If you want to give it a try? Buy a used one,so you don't loose that much money. If is the screen? Some people have had luck complaining to Samsung about it. They may provide a replacement screen,but you still have to pay a shop to install it. The T-Con board part number is... Samsung LJ94-02601F or this one depending on what screen is in yours. Samsung LJ94-02349C

hi it sounds like the lvds may just need cleaning also the connections on the tcon board hope it helps regards shaun

Return the set to the retailer. Sounds like a panel has come loose.

http://www.alibaba.com/ Try this link.

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power led, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating, to many popular brand TVs and other devices. Viewing it in "Mosaic" will make surf easy. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience.

2590,220184839

Please check the ribbons between TCON and panel. There seems some loose connection problem.

Check the backlight inverter board. It is faulty. There is no repair to these boards, if the inverter transformer on it is damaged. Card base replacement only can be done. To get more details, http://electronicshelponline.blogspot.com/

I have the exact same TV with the exact same problem. The issue is called diffusion and is not repairable. A Samsung repair tech can adjust the voltage settings but this will only work for a few weeks and cost a little more than $100. If you call Samsung they may be willing to issue you a new panel gratis (they did for me) but you will have to pay labor for the swap (about $400). If you do this the new panel will start to act up just like the old one so I would advise against it. Samsung will also claim that this is not a common problem which isn't true - especially for the 58" models which are seeing many extended warranty claims (which I didn't purchase).Best advice is to deal with it until you can't take it anymore and then buy a new TV but avoid Samsung in general and especially their plasmas. That is the route I am taking. And bashing Samsung for bilking me out of $400 6 months ago to replace a defective product with an equally defective one and then saying so sorry but you're now on your own.

Hi there,If the tv is still under warranty, this can be repaired at no charge.However, if not under warranty, you will need to have the CAPACITORS on the main power supply circuit board tested (or replaced).The capacitors responsible for the power supply can sometimes fail - open the back panel. If the capacitors on the main power supply board look too fat, or signs of burning near the solder joints, then you've found the problem.Hope this helps.Cheers,Scott

really need a model number to access this, you can try with tv off and within 5 seconds press from original remote control: mute 1 8 2 power, you should see a tech service menu, look for reset or virgin mode. Also may be listed as factory reset.

How do i reset factory sttings on showniv lcd tv

model:LD-f42HS90

You haven't provided sufficient information here to provide a solution to your TVs problem. Provide more details please. I there a screen? Is there sound output? Do the standby light at its front panel blinks during switch it on? If do, how many times it blinks at one time switch on?

i have tv samsung model samsung lcd tv model la32c400...when you open the power on. they have a raster but it is hung .up...and then we open again the power booton on pwer it is have only light display ...and also based side have small line ruster only 3cm....what cause this and problem the t-conn....has fixed already in lcd or disposable .....what is the solution on this parblem......some help.....plssss txt me 09991375154 thank u.....