20 Most Recent Canon PowerShot SD300 / IXUS 40 Digital Camera - Page 8 Questions & Answers


The wrist strap has a thin loop on one end. Thread this thin section (like threading a needle) through the strap hole. (It's on the left side of the camera. There are two openings with a bar over the top of the center of them at the bottom corner of the camera body.) Start threading from the middle of the body of the camera and push the strap towards the bottom of the unit. You may need to twist the loop to narrow it and keep it tight. Once you have this narrow loop through the camera, open up the loop and slide the thick material through the center of this thin loop. Pull the wrist strap until the thin loop tightens around the bar.

This is shown on page 12 of the D30 manual. The manual is available from Canon support on the Powershot page: http://gdlp01.c-wss.com/gds/5/0300013985/02/psd30-cu2-en.pdf. The direct link to the manual is http://gdlp01.c-wss.com/gds/5/0300013985/02/psd30-cu2-en.pdf .

I hope this helps.

Cindy Wells
(Many lanyard straps for electronic gear work the same way. Threading the narrow section under that bar does require decent near point vision. People who are far-sighted may need to wear bifocals or ask someone younger to assist.)

Canon PowerShot... | Answered on Feb 18, 2017


Get a card reader for your computer, if it doesn't already have one. The card will then appear as another hard drive, and you can transfer photos the same way you transfer any other kind of files.

Using a card reader is also likely to be faster than connecting the camera to the computer/

Canon PowerShot... | Answered on Jan 04, 2017


Each attempt to do what ?

Canon PowerShot... | Answered on Dec 28, 2016


Do you mean when playing video back on the camera? If so, when the video is playing, press on the top of the wheel, the part with the triangle pointing upwards (up-arrow). You should see the small volume level indicator get an increasing number of bars and the volume will increase.

Canon PowerShot... | Answered on Dec 12, 2016


Hi Charlie,
Please provide additional info if you really want help in this site. Questions with sufficient information do get answered sooner than others so consider that. Otherwise, check answers to previous questions of similar nature and you might locate a suitable solution for your question.

Canon PowerShot... | Answered on Oct 30, 2016


Just go to the Canon web site for manual download.

Canon PowerShot... | Answered on Oct 22, 2016


hi, go to the settings tab, you will find the language settings , this will surely work

Canon PowerShot... | Answered on Oct 03, 2016


This is an OLD camera that uses CF cards - the earliest type of card storage. I have provided a link to the manual for the camera - it is considered as Powershot S20 based on your PC1002 number. On page 21 of the manual (page 24 of the pdf) there is a table listing the compatible cards. Another Canon link (provided) states you can use CF Type 1 cards.

https://support.usa.canon.com/kb/index?page=content&id=FAQ100296


http://www.wedophones.com/Manuals/CamerasAndCamcorders/Canon%20USA%20Canon%20PowerShot%20S20%2032MP%20Digital%20Camera%20w%20Manual.pdf

Canon PowerShot... | Answered on Aug 30, 2016


Can you access the images on your computer ? If you can, then the fault lies in the camera. If you cannot, then the card may have become corrupted and you will have to rely on your backup copies.

Canon PowerShot... | Answered on Aug 03, 2016


Give the camera some time. Don't remove the battery till the reset is done. I hope your battery was charged before you started the reset.
If the battery runs out of power, you must charge it comlpete, before putting it in again. I hope the reset went well. If not only try a reset with a fully charged battery.

Canon PowerShot... | Answered on May 27, 2016


The camera's internal date/time "backup" battery is supposed to maintain the date/time for about 3 weeks with the camera turned off. If the camera is not used for a longer period, the date/time will need to be reset. If you are having to reset sooner than that, it is likely that the internal battery (not user replacable on most models) has failed.

Canon PowerShot... | Answered on Mar 15, 2016


Replace lens

Canon PowerShot... | Answered on Feb 18, 2016


hi,
it could be a software problem. if the camera doesn't get the battery's information this will occur the center terminal of the battery must be clean, similarly the contact inside the camera.
if it works for a little while, try to reset to default manner.

Canon PowerShot... | Answered on Feb 10, 2016

Not finding what you are looking for?
Canon PowerShot SD300 / IXUS 40 Digital Camera Logo

146 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts

old marine
old marine

Level 3 Expert

2260 Answers

Doberman

Level 2 Expert

261 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

PowerShot Canon

  • PowerShot Canon

Most Popular Question

setting date

  • Cameras
Loading...