Sony KP-57WS510 57" Rear Projection HDTV - Answered Questions & Fixed issues
Convergence repair kit used but problem is worse
did you check and replace the two pico fuses on the G board and also the six pico fuses on the D board? If so double check the solder often a pins mounting ring will lift up during the removal and prevent solder connection when doing the install.
My tv is not turning on but the stand by light is still on.
The model listed does not have a standby light, only the power on/off light which is there in case the set does not make it on to blink a error code--specific number of blinksbefore going further can you confirm the model number and add if have sound, or menu etc?
How do i find out if sony kp/57ws510 picture tube is bad
While the set is prone to bad tubes a double or 3d like image is convergence--this model uses two of the STK-392-560 CHIPS for this.Go into customer menu and call up convergence--if off and will not adjust in any area of the screen the chips are bad.
My tv works it looks Like the picture is three
The tv have a problems known as a convergence pictures problems.Tv have any colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board it is dead to causes this problems.The tv convergence board must have be fixed.The tv convergence board must have it parts replaced like 2 STK convergence ICS and some or all of it resistors too.To fixed the tv convergence board to solved the tv convergence picture problems.The tvs shops will cost u like $300-350 for parts and labors.
Hi,I have sony projection tv
You will have to install a convergence repair kit which will consist of both convergence ICs and the 8 associated pico fuses and the 4.7 ohm resistors will also need to be checked. Your model uses the Sony type 1 convergence kit. If you want to know where you get one they are available from
www.tvrepairworld.com they do include the parts and the CD with repair instructions.
I have a Sony KP-57WS510
The tv convergence board it is dead.The tv convergence board require replacing 2 STK convergence ICS and some or all of it resistors too.U have all the tools and also can do soldering ICS works?Yes,tries websites like Tvrepairworld.com,Tvrepairkits.com to buy a complete convergence kit parts for ur tv model and repair it ur self.Or the tv shop,will cost u like $300-350 for parts and labors.
3D look picture in rear projection tv is due to
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
SOLUTION
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Discoloration
Can you be more specific? Do you mean the color tints are wrong or is the color out of alignment ( 3D appearance)?
Convergence problem
Usually what happens is that the convergence IC goes bad or the fuse going to the convergence ic goes bad. Pico fuses they are called sometimes open up. You may want to open it up and pull the board out and check the solder connections on the convergence IC. Sometimes these get fractured or cold soldered and aren't making connection to the PC board.
Let me know if you feel comfortable with pulling TV chassis out or pulling the board that has the convergence IC on it out. Then you can resolder convergence IC OR replace it.First thing i would do is check to make sure there is between 22vdc and 25vdc on the fuse or the convergence IC. Let me know if this helps out any.... Sincerely HDTV GURU JAY
I have a sony kp-57ws510 and the colors are
Tv have a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadows or 3D pictures look alike?Tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.The tv convergence board must be replacing these parts to solved the tv convergence pisture problem.You have all the tools and can do basic electronic and soldering.Tries websites like Tvrepairworld.com,Tvrepairkits.com to buy a tv convergence kit that belong to ur tv model and repair it ur self.The shop will cost u like $300-350 for parts and labors.
Not finding what you are looking for?