20 Most Recent
Sharp AL-1217 Copier - Page 3 Questions & Answers
Paper jam light on
the censor that detect presence of paper in the printer has stopped working. check it if you can or get it repaired from local sevice centre......
Not picking up paper
check the paper tray and look at the side and end guide plates that hold the paper in place to see if they are loose you cab check this by pressing the paper down in the tray and see the guide plates pressing the edges of the paper.. if these are ok get a soft cloth and dampen just a little .. remove the paper tray and look at the rollers that feed the paper..give them a clean.They may have gotten dirty and the paper is slipping.. goo luck A
Red toner light was flashing.
Hi,
How about the green handle that locks the toner in place?
If it is broken the copier will never add toner because it opens the bottle to let the toner out. How about did you try to run in sevice mode to do a "Force Toner" and see what happens..
If you still have this red light toner flashing then the TD sensor got disconnected or is broken, the copier needs service because it's not detecting that it actually has enough toner inside to copy...
Please leave me comment, if you need further assistance
Rnj VINODKUMAR
Installing SharpAL-1217 on my Acer Aspire5701Z
If your system is running Vista, then U cannot install your sahrp copier for now until their is a compatible driver for vista.
But if U are using windows XP, then try downloading the Copier's driver from sharp.com
My Sharp AL-1217 keeps flashing H4 and does not respond
This is a typical fuser lamp issue. This is usually caused by a fluctuation in current supplied to the fuser assembly when the copier is warming up.
This cannot be solved by powering off the unit nor by unplugging it!
Follow the simple steps below to correct the issue:
- Power on the unit.
- When the LED display starts flashing "H" and "4", Press C and Auto button(this is the leftmost button with the copier console facing you)
- Repress the C and Auto Buttons again
- Press the copies button until 14 appears on the LED.
- Then Press the BIG Blue COPY button(the rightmost button with the copier console facing you)
Hurray, that's all folks
Flashing "L1" error
Hello,
A letter "L" and a number "1" appear alternately = The scan head locking switch is locked. Unlock the scan head locking switch.
Hope this helps. Good luck.
L1 is flashing on my copier
Hello,
Please check out the following website and see if you can find your error code: http://www.copier-help.com/copier-help/
Hope this helps. Good luck
Replacing Drum Catridge
Hello,
Here are the steps involved in replacing the drum assembly as copied from a users manual:
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies. When the internal counter reaches approximately 17,000 copies, the drum replacement required indicator will light up indicating that replacement of the drum cartridge will be needed soon. When the indicator begins to blink, the unit will stop operating until the cartridge is replaced. Replace the drum cartridge at this time.
1 Remove the TD cartridge (Toner Cartridge). Hold the drum cartridge handle and
gently pull the cartridge out. Dispose of the old drum cartridge in accordance with local regulations.
3 Remove the new drum cartridge from the protective bag and remove the protective cover from the cartridge. Then gently install the new drum cartridge.
When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. Do not remove the protective cover on the drum portion (black paper) of
a new drum cartridge before use. The cover protects the drum against external light.
Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies.
4 Gently install the TD cartridge. Close the front cover and then the side cover by pressing the round projections near the side cover open button. The drum
replacement required indicator will go out and the start indicator will light up.
Minolta Photocopier EP2030 service code
This code is related to the exposure lamp, Either the lamp is burnt or the fuse, a small device in the carriage of the lamp, is blown due to overheating. The reset is made with the machine switched on and by pressing the micro switch (right bottom corner) on the main board ( back of the machine).
GOOD LUCK.
Scanner Position Error
hi i think this is carrage home position sensor problem. u check and clean the sensor and try it back. or any forign meterial blocking in carrage way.. pls check that also.. all the best..
Not finding what you are looking for?