2008 kawasaki Ninja 250R Logo

Related Topics:

A
Anonymous Posted on Jan 16, 2014

2008 Kawasaki Ninja 250R no spark

I've tried almost everything an I cant get it to get any fire, I ain't got a clue, I've had it running last summer then lost my key now I put a new ignition on it an no fire maybe a relay or something @

1 Answer

Samuel Cooley

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on May 21, 2021
Samuel Cooley
Contributor
Level 1:

An expert who has achieved level 1.

Joined: May 21, 2021
Answers
1
Questions
0
Helped
569
Points
2

Needs a 100ohm 2w resistor installed on the gray wire inline between the ignition and the connector coupling.

  • Dennis Lilley
    Dennis Lilley Feb 23, 2024

    This guy is 100% correct I bet you used a different ignition

×

5 Related Answers

tbrat44

  • 86 Answers
  • Posted on May 27, 2009

SOURCE: how does a 2002 kawasaki ninja 250r act if the clutch isnt adjust

if there is no free play when pulling the lever in, the bike will most likely take off from first gear, but when you throttle it, the clutch will most likely slip. if the lever is to loose, lots of free play, you may have a hard time getting it in gear. approx 1/4 inch free play with the lever and it will work normal... unless its ready for a new clutch. hope this helps...

Ad

Anonymous

  • 1 Answer
  • Posted on Jul 12, 2009

SOURCE: my 2009 ninja 250r starts but dies when you remove

I had the same problem.. choke cable had to be adjusted. Check the manual, I don't have mine handy but the measurement is in there.. check it out.

tombones

  • 3567 Answers
  • Posted on Aug 08, 2009

SOURCE: My 2008 Ninja 250 tires to start itself

The switch is the most likely source of the problem. Check it with a volt ohmmeter. Put the key in off and check the terminals. Next turn the key to the 1st position and check the terminals then on any further positions. The next time the bike self starts is when you want to re-check the switch terminals.

You know, this has all the signs of an internal short in the switch. Just tell the dealer to give you a new switch. Switch failure after 5 hours of riding is simply unacceptable.

Anonymous

  • 376 Answers
  • Posted on Oct 04, 2009

SOURCE: need help

if its the right key, then use picks to extract the key piece, and have new one made. or find the largest red wire exiting the switch, apply power, may also be more than just this wire that needs power on some bikes.

Anonymous

  • 1 Answer
  • Posted on Jan 02, 2010

SOURCE: my 250r kawasaki ninja will not start, it starts

I have same problem on my 2007 250 it starts when I hold the choke when I release it it dies,my email is [email protected]
Thanks

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

How do i perform an oil change on my kawasaki ninja 250R?

http://www.kawiforums.com/ninja-250r/113982-2008-ninja-250-oil-change-procedures.html
1helpful
1answer

Ninja 250r 08fi 9000rpm sputtering problem when i drive my ninja and the enginge is cold then there are no problems with getting to the rev limmiter but once my bike gets warm then it starts sputtering at...

so i drove my bike sputtering to school and notice that there werent problems with the fuel system cause i heard the engine drowning in the fuel cause the ignition system couldnt explode it by a to weak spark from the spark plugs, so i only had to change the spark plugs and everything was good as normal

sorry if my story writings look a bit weird, cause i dont speak or write english where i live
0helpful
2answers

2002 kawasaki ninja 250 motor on ATV need wiring help

Hi and welcome to FixYa,

To my knowledge, there would only be 3 wires needed from the handlebars that affects the engine:
  • engine RUN/OFF;
  • clutch ENGAGED;
  • engine START.
The first 2 would go to the interlock plus the neutral wire and the sidestand wire. The interlock then sends signals that starter motor can turn and that CDI can fire.

As to the ignition coil, 1 wire is IGN B+12 while the other would go to the CDI and should pulsate when cranking or engine running.

Good luck and thank you for using FixYa.

0helpful
1answer

Passengaers

The max capacity or weight recommended by Kawasaki is 330lbs but you can ride two people max
Not finding what you are looking for?

579 views

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Bob G

Level 2 Expert

104 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...