20 Most Recent 2000 Honda Hornet 250 Questions & Answers

Look at the sidewall of both tires. There will be a "MAX PSI" embossed on the tire. It will probably say Max 45 PSI. At 45psi the bike will ride like a rock. At 15psi it will ride really squirrely. Find a psi at which you feel the bike handles well and rides well. One rider may weigh 125 pounds and the next rider may weigh 300 pounds. The best psi for each rider will be different due to weight. Chances are that 30 to 35 psi will do the trick. Please take a moment to rate my answer. Thanks.

Approx 22 psi. Both front and rear tyres.

NEVER the same pressure on both tyres !!
Usually, rear tyre is larger and/or carries more weight (you), therefore needs a much higher PSI. On a Hornet 250, 600 or 900cc it should be 36psi FRONT and 42psi REAR. - check the manuals.

It seems like you have bad spark. Try replacing you plugs. if it still wont run have your electrical system checked.

remove the right hand inspection hole from the engine cover turn the engine over with bolt in the hole and set the mark to no 1 tdc on remove the cam chain tensioner set the inlet cam with the inlet line mark flush to the head were the cam cover would sit then set the ex cam flush with the ex line and check that all three marks line up :inlet flush with the head the same with the ex cam and the crank mark lines up with engine case no 1 mark bolt down the cams in a criss cross pattern and torque to 12nm then back of the tensioner with a small flat head screwdriver you will have to hold it in the bolt it in and pull the driver out and you should hear it snap in place turn the engine over clock wise and recheck your marks to make sure you have it set wright.
hope this helps please leave feed back.

Auto parts stores (like AutoZone) usually have all kinds of shop manuals--even motorcycle.

there is normally marks on the flywheel. sometimes 3 sometimes less. find the mark that makes the left piston sit at top dead centre on the compression strocke and it should be lined up correct. make sure that u are happy before u try starting otherwise it could end up very expensive.

Clymer n Haynes publish them. Your library also has manuals in sec629. Some makes of bikes are similar so using other manuals may work

I am having trouble with your english translation of the symptom. However, if your bike starts and runs fine once it is warmed up and initially starts fine in warm weather this indicates a clogged choke circuit in the carburator and will require a thourough and proper cleaning of the carb.

Hi,

For all diagrams and other details,you need to have a service manual. You could view the complete service manual from :-

http://www.scribd.com/doc/9651858/Manual-Tecnico-Hondacb250

This service manual would have all the details you asked in the last few questions.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

theres a few things you can check

1. check the fuel filter
2. check the fuel lines ( no blockages )
3. clean the carb

Check the battery voltage and then battery voltage drop at starter relay (solenoid) If battery is good then replace the relay but make sure all your connections are good. If relay is good then replace the regulator/rectifier.

http://www.honda-tech.com/showthread.php?t=2531247

http://www.bikechatforums.com/viewtopic.php?p=2331885

To read the serial number on a Honda PC50 moped, follow these steps: Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places: Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567. Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body. Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it: The 9th digit of the VIN is a check digit. The 10th digit represents the year code. For example: A = 1980 B = 1981 C = 1982 D = 1983 E = 1984 F = 1985 G = 1986 H = 1987 J = 1988 K = 1989 L = 1990 M = 1991 N = 1992 P = 1993 R = 1994 S = 1995 T = 1996 V = 1997 W = 1998 X = 1999 1 = 2000 2 = 2001 3 = 2002 Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model; Additional Resources: If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped. Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.

Question edited for clarity and add magic word. The Owner's Manual covers basic repairs and is free. https://www.google.com/search?q=honda+anf125+innova+service+and+repair+manual

Honda ANF125 Innova Service and Repair Manual

Google Books https://books.google.com > ... > Repair & Maintenance The aim of this manual is to help readers get the best from their motorcycle. It provides information on routine maintenance and servicing and the tasks are ...

Honda ANF125 Manuals

ManualsLib https://www.manualslib.com > ... > Scooter Manuals and User Guides for Honda ANF125. We have 1 Honda ANF125 manual available for free PDF download: Owner's Manual ...

Honda Scooter ANF125 Innova Scooter (2003 - 2012)

Haynes Manuals https://haynes.com > en-gb > anf125-innova-scooter Detailed repair guides and DIY insights for 2003-2012 Honda Scooter ANF125 Innova Scooter's maintenance with a Haynes manual. ..

The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.

Question edited for clarity, but no idea what you mean by - "What do I need to do to get the gay? The clutching gauge in again?" You issue is probably that all the clutch plates are glued together. Leaving a bike for 21 years will do that. https://www.google.com/search?q=1985+Honda+Gold+Wing+1200+stuck+clutch ..

Check the wiring, especially the engine earth lead.

On the bottom of your speedometer on the left side there is 2 buttons press the far left one for a couple of seconds and the light should go on