1992 Chevrolet K1500 Logo

Related Topics:

Posted on Jul 03, 2011

Im working on a 1993 GMC 4.3 MOTOR and the timing on the intake is def.then what every one has show n me on my intake it has on driver side 135 on passenger side its either 264 or 462 but the 6 is in the middle of the intake

  • Jeremy W.
    Jeremy W. Jul 03, 2011

    What is your question?

×

5 Related Answers

Anonymous

  • 52 Answers
  • Posted on May 13, 2009

SOURCE: 03 cavalier wiper on driver side is out is it fuse or motor?

you need to remove both the wiper arms. Take off the rain seal from under the windshield. remove the cover underneath you will find the rod has worn and dropped off you must get a complete new mechanism. Or if you cant afford to do that re attatch the rod to the buckle pin on the wiper arm and use some insulation tape to make a temporary repair till you can get a new one.

Ad

Anonymous

  • 462 Answers
  • Posted on Jun 18, 2009

SOURCE: passenger power window does not work 2002 Silverado HD Ext Cab

REMOVE THE DOOR PANEL TO GET TO THE WINDOW MOTOR. REMOVE THE CONNECTOR ON THE MOTOR. LOOP A TEST LIGHT FROM BOTH TERMINALS. WITH THE KEY ON AND BOTH SWITCHES IN PLACE, CHECK TO OPERATION OF THE SWITCHES. IF THE LIGHT COMES ON IN BOTH DIRECTION THE WINDOW MOTOR IS BAD.

THERE IS A CIRCUIT BREAKER BUILT INTO THE WINDOW MOTOR. SOMETIME HITTING THE MOTOR WITH MAKE THE CIRCUIT BREAKER RESET BUT THE MOTOR WONT LAST LONG DOING THAT.

ALSO TRY PULLING DOWN ON THE WINDOW WHILE TRYING THE SWITCHES. THE WINDOW COULD JUST BE STUCK. THIS HAPPENED TO ME.

Testimonial: "Thanks, BB1BUD. I ended up replacing the entire regulator with a part I ordered online. So far so good."

Anonymous

  • 986 Answers
  • Posted on Oct 30, 2009

SOURCE: Where are the timing marks on a 78 gmc 1500

on your harmonic ballancer,sound like your pointer is missing,When you look down at your Harmonic balancer there should be something about it that you see that looks kinda like saw teeth with numbers in the gaps. The zero or line whichever year you have should be on the Harmonic balancer

Anonymous

  • 1450 Answers
  • Posted on Feb 16, 2010

SOURCE: 1993 4x4 gmc 1500 lights up and shows 4 low but

you need to replace the front actuator on differential it was a common problem for these to go out

Anonymous

  • 4669 Answers
  • Posted on Dec 02, 2010

SOURCE: 2002 Chevy Venture 3.4 L 6 cylinder firing order.

135 is on the back and 246 is on the front. From passenger side to drivers side. Number 1 cylinder is the one under the alternator.

Testimonial: "Thank you very much."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How many o2 sensors do I have on a 1993 gmc seirra

I believe the 93 Sierra has only one O2 sensor. It is in the manifold on the drivers side. This assumes the 5.7L motor.
1helpful
1answer

Spark plug gap

the spark plug gap for gmc sierra with the 350 ci 5.7 is 0.35 Im not sure what it is for the other motors but if you have a 350 in a 1993 sierra its 0.35 I know this is correct because its on the sticker under my hood and im changing my oil right now so I just read it about 20 seconds ago....
0helpful
1answer

Will bad timing effect gas flow to engine

Yes it will, if the intake valves dont close on time, the piston is coming close with some compression which will sent back to the intake.
I hope this helps!
0helpful
1answer

I wanted to know the firing order for a 1993 Chevy s10 4.3 litre. And where no. 1 cylendar is located?

1-6-5-4-3-2 and 135 is on the driver side and 246 is on the pass so no 1 is the front cyl on the driver side hope that helps
0helpful
2answers

What is the distributor firing order for a 350 1993 gmc

The firing order should be stamped on the intake manifold itself.
0helpful
1answer

What are the timing specs on a 1993 GMC Sierra Z71?

theres no advance wire on that engine!!! theres a hash mark on the back of the intake and one on the distrbutor shaft you set the distrib with the has mark and yes!! the ecm! will always reset the timing that is what is does but if it's pinging or knocking then change the ignition module cause the dwell side of it is out of range!
2helpful
3answers

1997 gmc sierra 4.3l new fuel pump and wont start

I have 1993 gmc 4.3 vortec v6 turns over but want start. replaced fuel pump, fuel pump regulator ,ecm, tps, coil
0helpful
2answers

S10 4.3 and need diagram to reattatch wires to post.

I would buy a car repair book for future reference and next time you change them, do one at a time that way you can match them up and get them all on and not worry about losing their place.
0helpful
1answer

1999 GMC Sierra 5.3L knocking sound around Catalytic Conerters? ?

on my gmc i have 2 knock sensors and im not possitive if you have two or not under your intake mani but when i replaced both mine i got the same code of low input so i took the small needle out and wire brushed it clean and also traced and ran a new wire just to be safe and that solved my problem. as for bank 1,2 if it helps any my bank one is located engine side driverside and bank2 is engine side passenger side and 3 and 4 are underneath bed side. but you can see the sensors if you look real close near the headers. hope this helps
See less
Not finding what you are looking for?

34 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...