Would like to remove drivers door exterior handle.I have already removed 2 rubber gromets from the side of the door and removed torx screw from inside of top hole to take of the outer part of the handle surounding the door lock,but how do i get the rest of the handle off.Would like to remove drivers door exterior handle.I have already removed 2 rubber gromets from the side of the door and removed torx screw from inside of top hole to take of the outer part of the handle surounding the door lock,but how do i get the rest of the handle off.
AnonymousMar 23, 2014
handle cannot open latch,how do i remove and replace door handlehandle cannot open latch,how do i remove and replace door handle
You can't post conmments that contain an email address.
Lower hole in the door jamb loosten allen screw until the cap comes off. Upper hole there is a #20 torx slightly down and inboard of the hole, you need a really long torx bit and pull the handle out slightly. It also helps to pull weatherstrip loose so you can see it.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You have to remove the door panels and this takes special tools. Then you remove the window and then you can get to the door handle mounting bolts. It might just be the linkage to the latch from the handle.
Remove inner door handle and arm rest if applicable, with a flat screw driver or chisel leaver door cover away so as to gain access, undo the screws on old handle,remove rods ,then remove handle fit ,new handle .mark rods with paint so they go back in the same place.
This would involve most likely rolling window to the bottom as far as it will go and then opening door. Remove door panel and trim and use a flashlight to look for the fasteners holding this to the door. This should have 1-2 rods that are held in place by plastic locking pieces and clip to the outside of the rod and I side the whole in the handle.
As per the Haynes manual for your vehicle.
DOOR WINDOW GLASS-REMOVAL AND INSTALLATION:
1. Remove the door outer panal.
2. Lower the window glass.
3. remove the two nuts and one screw securing the glass.
4. Remove the glass by lifting it up carefully and rotating it inward.
5. Installation is reversal of removal.
DOOR OUTER PANAL-REMOVAL AND INSTALLATION:
1. Remove door trim panal.
2. Remove the outside mirror. Remove the foam block from the mirror opening.
3. Remove the outside door handle.
4. Open the door and pry thhe outer sealing strip out of the window glass opening.
5. remove the door panal screws.
6. Detach the front and rear of the outer panel, then lift it toward the rear to remove it.
7. Installation is the reverse of the removal procedure. Apply thread locking compound to the panel retaining screws.
OUTSIDE DOOR HANDLE-REMOVAL:
1. Pull handle out and puch the centers of the retaining pins through the pins, then remove them and detach handle. (These pins are located underneath the handle.
Hope this helps, let me know if you need any other help.
good day, well sir your so close from opening the doors. if you find the metal wiring that connects to the door lock then you have to force it a little to let loose. Its gonna be a little tight coz the electronic lock is still connected. if its too tight try removing the steel wires from the power lock connection then try letting the steel wires again. hope this helps and have a nice day.
go to ebay motors and search your year make model then service repair manual obtain a cd repair manual it has extensive wiring schematics and electrical component locator in it along with repair procedures and illustrations for about $20.00
If it's the outer panel the door handle is held on with a small push pin.You remove the inner portion & then remove the outer part.Then lift door handle up & slide forward.It shoukld come off.1996-1999 Sedan the regulator can be removed with just the inner door trim removed.hope this helps
Would like to remove drivers door exterior handle.I have already removed 2 rubber gromets from the side of the door and removed torx screw from inside of top hole to take of the outer part of the handle surounding the door lock,but how do i get the rest of the handle off.
handle cannot open latch,how do i remove and replace door handle
×