Cars & Trucks Logo

Related Topics:

Posted on May 10, 2010

How do i replace the speakers in my 1992 gmc sierra?

  • Marvin
    Marvin May 11, 2010

    all of them?

×

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 17 Answers
  • Posted on May 11, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: May 11, 2010
Answers
17
Questions
0
Helped
8431
Points
65

All the trim pannels just pop off in the back factory replacements are 4x6 front and rear be carfull anyway you can break the clips

5 Related Answers

Anonymous

  • 1118 Answers
  • Posted on Feb 14, 2009

SOURCE: Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Ad

Anonymous

  • 59 Answers
  • Posted on Mar 15, 2009

SOURCE: 1997 GMC Sierra Ignition Switch Replacement

take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

cy schousboe

  • 2002 Answers
  • Posted on Jun 18, 2009

SOURCE: I have a 1992 GMC Sierra with a 5.7 motor. When

It sounds to me like your transmission is not well. It's working when the fluid is cold but not as it warms up. Pull the dipstick and check your transmission fluid for color and smell. It should be pinkish and smell like oil. My guess is that it will be closer to brown than pink and have a burnt oil smell to it. It the transmission is full, check the level with the trans warm,engine running, in neutral.I'd be shopping for another transmission. If the fluid is below the add mark, you an usually buy yourself some time on the replacement by changing the trans fluid and filter.At the same time add a transmission treatment with the new oil,I've had good luck with Lucas. Hope this helps.








Joseph Howard

  • 753 Answers
  • Posted on Aug 31, 2009

SOURCE: How do i remove the headliner board from gmc

You remove any of the trim that is contacting the headliner,remove light in the center,remove visors and any hooks that are there to hang things on ,Most of your trim has push in retainers handles and hooks,seat belts should have screws inthem.

Anonymous

  • 3 Answers
  • Posted on Sep 17, 2009

SOURCE: replace sway bar end links '97 GMC Sierra

if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I replace a bad tripometer in my 1992 gmc truck 1500 sierra z71

Try pushing the button repetedly wal drivering
It likey will start working again
Dust or else is binding the plastic gears














0helpful
1answer

1992 gmc sierra pickup gas gauge always reads full

REPLACE SENDING UNIT THAT'S INSIDE THE TANK
0helpful
1answer

I have a 1992 gmc sierra and when I tried to start it nothing happened, I replaced the starter and now all that happens is that the starter keeps clicking. Any ideas?

did you replace the starter solenoid, it sounds like the linear motion is there in the starter, just no turn. check the solenoid
1helpful
2answers
0helpful
1answer

If I replace the engine computer in my 1992 GMC Sierra do I have to have it programmed or is it already done

It should be a plug and run solution. The new computer may take a while to relearn all the input from the various sensors but after running a while all will be well.
2helpful
1answer

Where is the fuel filter located on 1992 sierra 1500 located

It is located midway along the frame of your truck.

Remove the fuel filter from the bracket on the frame rail. Replace the fuel pipe O-rings if you find any cuts, nicks or distortion in them. Slide the new filter into the bracket. Remove the caps you put on the fuel pipes and connect the threaded fittings back to the filter. Tighten it to 18 ft-lbs.


Read more: How to Replace a Fuel Filter in a GMC Sierra ' eHow.com http://www.ehow.com/how_4507468_replace-fuel-filter-gmc-sierra.html#ixzz14Xs33Ii1
1helpful
1answer

Replacing starter on 1992 gmc sierra 305 v8 motor

disconnect the battery lead from the starter plus other wires,undo the bolts on the starter flange & the starter should pull straight out providing there is nothing else in the way if there is anything it will have to be removed first.......hope this helps......cheers
1helpful
1answer

Where is the air conditioning relay for a 1992 gmc k2500 sierra? I just replaced my compressor and dryer today and the compressor wont cycle on so i can charge the system.

Compressor won't start until there is at least 45lbs of pressure in the system.The relay is in the underhood fuse/relay center.
0helpful
1answer

My a/c only work on the high position.

replace the blower motor speed control resistor.
3helpful
1answer

Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.
Not finding what you are looking for?

305 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...