TDS 3-button keyless remote operating instructions please

You need to contact Toyota on this question.

the operators guide cover this.
hot reprogram key fobs , all cars. have the book in the glove boxl
and tells you how many keys you must have (WORKING) TO make a new key, some take 2 or 3 key s to DIY..

ask toyota for the guide. its free sometimes. (i wax safety issues and bam free, tell engine will not idle can car is dangerous.. bam. free guide.)

or go to , "buy a new key fob dot com." goggle finds them easy.
pretend to buy and aftermarket key
and bam free instructions. wow huh:?

follow this link for a step byu step guide
Camry programming instructions for TDS Rostra keyless entry remote FCC...

Great news, your 1998 Toyota Camry Key Fob is self programmable. Below are the programming instructions. Be patient, it might take you a few times to get this right. It is all about timing.

Most remotes can be self-programmed. If this procedure does not work, you must have your remote programmed by a professional automotive locksmith or dealership.


Obtain all remote transmitters for this vehicle.
1. Insert key into ignition and turn ignition switch to ON position.

2. Locate the ECU (Engine Control Unit) and press and hold the ECU PROGRAMMING button for 3 seconds. The ECU will be located under one of the front two seats, the trunk, or under the dashboard on the drivers side. You will need a small pointy object like a pen to depress the ECU button. After pressing the ECU button for three seconds, you will see the STATUS MONITOR LED turn on for 5 seconds. Vehicle is now in programming mode.

3. Press and release the top button on the remote. The STATUS MONITOR LED will turn off. A chirp will be heard as well as one flash of the exterior lights.

4. Turn off the ignition. Programming is now complete, test remotes for proper programming.

The vehicle must be locked, so press the lock button and verify doors lock, then press the start button twice.

Key less car has a remote with usually 2 or 3 buttons on it. The remote has a small key blade which always resides with in the remote and can be pulled out by pressing the release button located on the side of the remote. Another indication is that the car does not have any key cylinder but has a smart round push button placed on the dash to start and switch off the engine.

Go to yahoo.com and ask how to program fob.,

Hi, Stacie,

here's the instructions for a 97 TL - I hope they're the same.

Note:
Entering the programming mode cancels all learned keyless remotes, so
none of the previously programmed remotes will work. You must reprogram
all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep
the system from exiting the programming mode. You must program remotes
within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes.
(An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote
used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote.
Make sure the power door locks cycle to confirm you are in programming
mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote.

8. Within 10 seconds press the LOCK or UNLOCK button on all other
remotes you want to program. Make sure door locks cycle after you push
each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)

Hope this helps :)

John

sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!

Okay, here goes-

1. Turn Key to on position.
2. Push and hold **valet button on the stock radio.
**Valet button is skinny bar located between am/fm & cd/tape buttons on stock radio.
Door locks will cycle one time.
3. Press any button on remote one time within 20 seconds. Door locks will cycle again.
4. To program up to 4 additional remotes repeat step 3 for each additonal remote.
5. Turn key off programming is complete.

Thanks for using Fixya, please rate if this helps :)