How to remove a headlamp assy from a 1998 jeep grand cherokee

1998 ATC Jeep Grand Cherokee Blower Resistor connector ...

? 0:55
www.youtube.com/watch?v=sDFLuenx9aw
Nov 14, 2012 - Uploaded by Freedomautomotive1
1998 ATC Jeep Grand Cherokee Blower Resistor connector Repair Kit (RARE 1/2 Year) ... How to Fix a Chrysler Blower FanThat Only Works on High - Duration: 16:51. ... JEEP2001 FIXING THE HEATER BLOWER CONTROL. ... Jeep Grand CherokeeCenter and Lower Dash Removal - Auto Repair Series ...

There should be one screw that hold the top of the headlamp assembly to the upper radiator support. It is either a 9/32" or an 8mm. Once that screw is removed pull out on the headlamp assemble. It should pop out. Sometimes you will need a large screwdriver to pop the metal mounting balls out of the sockets. You can just barely see the inside one if you look on the back of the headlamp assembly. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

You need first remove jack screw attaching top of headlamp mounting module.
Grasp upper inboard and lower outboard corners of headlamp and forcefully pull headlamp outward.
Remove bulbs sockets and separate headlamp from vehicle.

Also, I suggest chek your Jeep WJ REpair Manual Section-08L-Lamps-Ewj8l for more details and graphics.

Hope helps with this. Good luck (remember rated this help)

give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local Jeep dealership in the parts department and they be able to print you off the pictures and diagrams you will need wish you the best of luck Michigan Man.

Remove the jack screw attaching the top of headlamp to the headlamp mounting module.
Grasp upper inboard and lower outboard corners of headlamp and pull headlamp outward.
Remove all of the bulb sockets from headlamp module.
Separate the headlamp from vehicle.

Bulb removal:
Remove the headlamp.
Turn the bulb socket one quarter turn counter clockwise.
Remove the socket from lamp
Remove the bulb from socket

To install, just do everything in revers and take extra care not to touch the new bulb to ensure a long life. Good luck and hope this helps.

It lives under the right headlamp below the plastic bracket that holds the headlamp assembly. You can gain access one of two ways. Remove the bumper fascia, headlamps, and bracket that runs across the front of the car. Or, remove the right headlamp and use a hole saw to drill a one and a half to two inch hole in the bottom of the bracket. Once the headlamp is back in place the hole won't show and the integrity of the bracket will remain.

1. Disconnect and isolate the battery negative cable.
2. Remove the headlamp cover TOP
   1. Remove the mounting fasteners.
   2. Disconnect the headlamp unit electrical connector BACK
   3. Separate the headlamp from vehicle.CAUTION: Do not touch the bulb glass with fingers or other oily surfaces. Reduced bulb life will result.
      
      NOTE: If installing a new headlamp unit, transfer all the wiring, bulbs, and sockets to the new unit.
      
      
      1. Install all of the bulb sockets in headlamp .
      2. Position the headlamp on the vehicle.
      3. Connect the electrical connector .
      4. Push the headlamp inward to secure into position.
      5. Install mounting fasteners
      6. Install cover over headlamp.
      7. Connect battery negative cable

The headlamp assy. actually snaps into place. With a screwdriver very carefully pry the headlamp assy out on the top. The assy. will make a snapping noise, don't woory you did not break anything.

first remave the headlamp and then remove the marker lamp assy.

the only problem that vehicle has is with cooling fans is relay/module or electrical harness to module that burns up located behind and under right front headlamp assy must remove headlamp to access relay/module that is what powers up fan motor module assy.