99 honda accord, manual, 5 speed. vehicle won't

accord stalling on every stop. (1/2) - EricTheCarGuy ...

www.ericthecarguy.com/.../8.../46884-accord-stalling-on-every-stop

The car runs good but stalls every time i come to a stop. ... a stop then it diesagain.only on the stops does the idle drop very low to the point of stalling.what ... only when I start slowing down and come to a complete stop RPM's go down and the cardies. ... The popular Honda Civic and Accord vehicles share many powertrain ...

1998 Honda Accord loses rpm/ stalls coming to a stop ...

honda-tech.com/honda-accord.../1998-honda-accord-loses-rpm-stalls-co...

Jan 10, 2013 - I just bought a 1998 4 cyl 2.3 L Honda Accord two days ago. ... 1998Honda Accord loses rpm/ stalls coming to a stop. .... Is clockwise high idle or low idle? all in all i probable rotated counterclockwide 1.5 or 2 turns. maybe this ...

1999 Accord, 130k+, stalls when slowing to a stop - Honda Accord ...

www.hondaaccordforum.com > ... > General > General Tech Help

Mar 10, 2010 - My fiancee's '99 Accord EX Coupe 4-cylinder automatic, with 130,000+ miles, has recently (in .... No low RPM & feeling like it's GOING TO stall.

99 Honda Accord - Strange Stalling Issues! HELP!

https://www.2carpros.com/.../1999-honda-accord-99-strange-stalling-issu...

My 1999 Honda Accord is having sporadic stalling problems. I've noticed a pattern. Itstalls while going slow speeds and stop and go traffic, etc. The engine just ...

Stalling or Low Engine Idle Speed Due to Dirty ... - Repair

Are you saying the starter is grinding but the engine is not cranking, or the engine is cranking and making noise and not starting ?

Park neutral safety switch maybe be the reason for the no crank ! Try putting the vehicle in park ,then try to crank the engine . Testing the electrical circuit is the best way to trouble shoot this problem , along with do a voltage drop test on the starter circuit ! This will test the battery cables an connections .
Starter Voltage Drop
How to voltage drop test starter motor circuit
Does it have a manual or automatic transmission ? Manual ? clutch switch . Looking at a wiring diagram I also see a starter cut relay !
http://www.bbbind.com/free_tsb.html Free wiring diagrams . Enter vehicle info. year , make , model and engine size . Under system click engine , under subsystem click starting . Then click the search button , then click the blue link ! Check the starter cut relay also . Videos on youtube showing how to test a relay controlled circuit !

Your main power relay is causing that hot, no start problem.

With manual vehicles you should check your sensors near the clutch. I had spark and gas and would not get a click. There are two sensors under the dash that when you push the clutch in, it allows a deactivation . Which allows the starter to engage. Both sensors have a push rod end to them where you can push in and out. There are two grommets that are made of plastic that tend to wear down that press against the rod pushing them in. Once they break off...there is nothing to activate the sensor..hope this helps. Thanks Ram210

i have two things that come to mind first of which is your neutral safety switch ...its located on the clutch pedal ..its to prevent the car from being started in gear it may not be working correctly and wont let power to the started when you turn the key...most likely the problem...the other thing if thats not it you may need to check the ignition switch...

Ensure your spark plugs,wires (ignition coil and spark) and your filters (air and fuel) are within 2 years of installation It's erratic at 800 rpm as the engine is cold and they like the 2200 range for 3 minutes before they kick down on their own. Press the pedal twice before inserting your key. The owners manual states depending on the outside temperature, the engine will require more priming. Update if possible.

Change the ignition switch at key.

Sounds like an ignition module problem. Not to hard to change, they are inside the distributor.

DISCONNECT BATTERY FIRST !!!!!!! THE START MAY NEED TO BE GAINED FROM UNDERSIDE OF VEHICLE,, RAISE VEHICLE AND SUPPORT ON AXLE STANDS !! UNDO WIRING FIRST THEN UNDO BOLTS/BRACKET..