Lost the key fob that came with the car brought a new one on eBay needs to be program
You can't program a Mercedes CLS 500 Key Fob without special programming equipment. There are some automotive locksmiths that have this equipment, but not many. I would still try to find a locksmith as they are usually more affordable than the dealer.
SOURCE: 2003 Jaguar S-Type, programming a key fob
The switchblade key would need to be compatable with your ignition switch barrel. Only normally available from jag dealers who check the Jag owners register before supplying you a replacement.
The older type seperate fobs could be programmed by switching the ignition on and off 8 times (allowing all functions to settle) and on the 9th switch on - press a button on each fob and then switch off. to test use a good fob to lock the car then try the reprogammed fob to unlock/lock. Sometimes this works first time - sometimes needs a couple of tries.
SOURCE: how do i program a key fob for a 2006 Pontiac
you will need to take it to a dealer or some place that has a scanner to program key fobs
IMORTANT TAKE ALL THE KEY FOBS WITH YOU
once the vehicle is put in the learn mode all the fobs have to be programed
SOURCE: How do I reset a Key Fob for my 2006 Grand Prix
No Tools Required
In the event that a transmitter is lost,
program the old and the new transmitters into the memory of the remote
control door lock receiver. Up to 4 transmitters may be programmed.
Important
Once the keyless entry receiver enters the
programming/diagnostic mode, the programming of the first transmitter
erases all previous transmitter programming information. You must then
program all of the transmitters.
Program only 1 vehicle remote control door lock receiver at a
time. If you program multiple receivers simultaneously, the same
transmitter could possibly be programmed to more than 1 remote control
door lock receiver.
Perform the following steps:
Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open
and then close any vehicle door. You will hear a chime when the remote
control door lock receiver enters the programming/diagnostic mode. If
you do not hear a chime, start again at step 1.
Important
After 7 seconds, you may hear a chime confirming
successful synchronization. After approximately 14 seconds, you will
hear a chime confirming successful programming.
Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation
SOURCE: Hi I want to program a new keyless fob. I have
1. Close and lock all doors with the driver’s side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.
SOURCE: programing instructions for buick 2006 lacrossekeyless remote fob
Transmitter ProgrammingImportant:
All transmitters which are to be recognized by the remote control door
lock receiver (RCDLR) must be programmed in a single programming
sequence. If the system is placed in program mode it will erase all
previously programmed transmitters upon the receipt of the programming
signal from the first transmitter. Up to 4 transmitters can be
programmed. Do not operate or program the transmitters in the vicinity
of other vehicles that are in the keyless entry program mode. This
prevents the programming of the transmitters to the incorrect vehicle.
Good luck
1,851 views
Usually answered in minutes!
×