In my 2005 hyundai xg350l there's a fuse box around kick panel..the "Start fuse " has no power but fuse is good. Fuel pump is new engine crank but wont start..help please..thank you

The fuse is in the engine compartment fuse box and is marked 'A/Con'. It looks like a Relay to me and as it doesn't have an amperage, my guess is that it is a relay. The different sites have slightly different variations, but the thing to check first is the relay. You mention 'heater coil', that is on the engine coolant circuit and only provides hot air. The AC compressor system has an 'evaporator' up in the dash and only supplies chilled air. I trust the AC job was done professionally with a Gas Recovery machine to create a moisture free vacuum before adding refrigerant gas. It can't be done at home. I wrote a Fixya Tip on it.

Hyundai Tucson (JM; 2004-2009) fuses and relays

Fuse Box Diagrams https://fuse-box.info > hyundai > hyundai-tucson-jm-2...

Here you will find fuse box diagrams of Hyundai Tucson 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside ...

2005 Hyundai Tucson fuse box diagram

StartMyCar https://www.startmycar.com > Tucson > Fuse box

2005 Hyundai Tucson fuse box diagram. The 2005 Hyundai Tucson has 2 different fuse boxes: Engine Compartment diagram. Inner Panel diagram.

Hyundai Tucson 1 (ix35) - fuse and relay

FuseAndRelay.com https://fuseandrelay.com > hyundai > tucson-1

It is located in the left end of the dashboard, behind the protective cover. ... The fuses designated as C / LIGHTER or P / OUTLET are responsible for the ...
https://www.google.com/search?q=2005+hyundai+tucson+ac+relay+location

..

usa car what engine, G16, J20 or h27(v6)
toss coin H27 v6
2 fuse boxes one in engine bay
1 at USA drivers left toe kick panel and up/
"FI" fuse must be good.
relay called double relay runs the fuel pump.

cranks but will not start
the IMMO lamp on dash must not be unhappy per uses guide or fuel is cut dead;. on all cars with IMMO
next scan the PCM for DTC errors.
like
DTC P0230 FUEL PUMP SUPPLY CIRCUIT MALFUNCTION?


fuel pressure wrong (suspected)

the test is 2 fold. not guessing what is wrong.1
1: out of spec or dead ,fuel pressure at the rail cranking.

2: If that fails voltage at the pump not 11 to 12vdc cranking.

ecu 1 connector below

No it doesn't . Has fuel pump relay controlled by the PCM - powertrain control module . The PCM needs to have inputs from crankshaft position sensor before it will energize the relay . Does the vehicle have spark at the sark plugs or coil's ? If there is spark the crank sensor is good . Would need to do fuel pump electrical circuit testing , like this
Testing Electric Fuel Pump Problems with Voltage Drop Test Look at the fuse / relay box under the hood in engine bay . Find fuel pump relay . Do you know about relays an how they work ? Videos on youtube .

images for Where is the ECM fuse and Fuel pump ..

ECU fuse keeps blowing - New Tiburon Forum : Hyundai Tiburon ...

www.newtiburon.com/.../tiburon.../217243-ecu-fuse-keeps-blowing.html

Sep 8, 2012 - 18 posts - ‎8 authors
Edit: Instead, pull the fuel pump relay, and see if the fuse still blows when ... ControlRelay, Fuel Pump relay, A/T control relay, Generator, ECM ... Official "Check Engine Light" Thread - New Tiburon Forum ...
Jul 22, 2014
Fuel pump Relay
Apr 26, 2013
Starting problem. Fuel pump doesn't prime with key on.
Mar 9, 2013
Fuel pump not starting intermittently
Oct 6, 2010
More results from www.newtiburon.com

Car Cranks But Will Not Start - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...2000.../85246-car-cranks-but-will-not-start...

Jan 17, 2008 - 10 posts - ‎6 authors

check the fuel pump inertia switch behind the passenger side kick panel. Also make sure connections are tight and not corroded. Then you might consider a new ignition switch from autozone for $25.

I had this problem with a 1991 ford taurus. The fuel pump relay went bad.

Crank no start could be
1. Fuel inertia switch ( passenger side kick panel )
2. Fuel pump relay or fuse ( fuse replaceable relay is built into the fuse panel )

3. Most common for crank no start is the FPDM ( Fuel Pump Driver Module ) on the cross member by the spare tire.
Lower the spare, and check to see if the module is cracked.
This is what mine looked like on my 2006, the housing was cracked, but the PCB was still good ( I did not have a problem yet )

The cable on the right side of the picture is the spare tire lift, and the picture is taken facing the front of the truck.

First of all, Hyundai did not produce the XG350 until 2002. You wrote 2001 Hyundai XG350L. The engine in the 2001 is 3.0 (XG300). Cant help you.

Hi there, 
If you can get under the car just head to the petrol tank and look for the lines running to and from the tank,
There should be several thin copper looking metal tubes running from the tank to the engine bay,
Generally somehwere along that line should be the fuel canister that should look almost the same as your new one, 
Its then a simple process of unscrewing the old one and screwing in the new one, Be aware not to use any sort of flame light ie lighter when under there as fuel will run out when you remove the old one. If its not under ther then it will be mounted in the engine bayas before just follow those tubes.
You may need to turn the igition on and off a few times once installed to prime the lines if the car does not automatically do this.
If it still wont start try pumping the gas/accelerator once or twice,
Be carefull not to flood the car and you should be away.
Hope this helps
Cheers
Steve