Can you show me a video how to remove and replace a coolant temperature sensor to a mercedes 1989 190E 2.6 6-cyl

The temperature coolant sensor on a 2017 Cadillac CTS with a 3.6-liter 6-cylinder engine is typically located near the engine block, typically in the lower radiator hose or the engine coolant outlet. However, it is best to consult your vehicle's service manual for the exact location as it may vary depending on the model and engine type.

Question edited for clarity.
Question moved to model category.

Shown here

https://www.vwvortex.com/threads/coolant-temerature-sensor-location.9246449/

Videos

https://www.google.com/search?q=2017+Volkswagen+Tiguan.+Coolant+temperature+sensor+location

..

limited info generic answer https://www.youtube.com/watch?v=Guq-CZtFyhg https://www.youtube.com/watch?v=baIhe5UBrGI

At the rear of the right cyl head

Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.




Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

According to Autozone.com:

Because ECT (engine coolant temperature) sensor procedures vary depending upon their location, first locate the part. You may need to partially drain the engine coolant to prevent coolant spillage.

• Disconnect the negative battery cable.
• Unplug the ECT.
• Then, unscrew it.
• Reverse the removal procedures to install the new part.
• Connect the negative battery cable to the battery.

Related Parts:



Cooling Fan Switch
Content for class "spacer" Goes Here

Engine Temperature Sensor
Content for class "spacer" Goes Here

Temperature Switch
Content for class "spacer" Goes Here

---
Coolant Temperature Sensor

Fig. Remove the coolant temperature sensor
The coolant temperature gauge sensor is a temperature-variable resistor, or thermistor. As coolant temperature increases, the resistance of the sensor decreases or decreases, depending on the type of sensor.
A1 and A2 platforms use a different type of circuit that A3 vehicles. On A1 and A2 vehicles, the circuit is a "resistance to ground" type. A3 vehicles use a "variable voltage" type, where a voltage is supplied to the sensor. Because of the circuitry design on A3 vehicles, testing of the coolant temperature gauge is limited.
The engine coolant temperature gauge uses a heat sensitive sending unit to transmit an electrical signal to the gauge. The sending unit is a heat sensitive variable resistor that is located on or near to the cylinder head and threads into an engine coolant passage. The sensors are a Negative Temperature Coefficient (NTC) type. As the temperature increases, the electrical resistance of the sensor decreases. As the coolant temperature changes, so does the resistance of the sensor. The gauge is calibrated within the operating range of the sensor and interprets the resistance value to display the coolant temperature.
Beginning with model year 1994, the engine coolant gauge and the Engine Control Module (ECM) temperature sensors were combined into one sensor with 4 terminals. The basic operation remains the same in that their resistance decreases as the coolant temperature increases, however the actual resistance values of the 2 sensor circuits are different. The electrical connector of the 4-wire terminal sensor ( 1 and 2 ) is keyed to prevent improper connection of the sensor's electrical circuit.

Fig. Beginning with model year 1994, the Engine Coolant Temperature Sensors combined the sensors for the ECM and the gauge into one sensor-1997 2.8L V6 sensor shown

Fig. The electrical connector for the combined temperature sensors is keyed to avoid improperly connecting the sensor's wiring-1997 2.8L V6 connector shown

4.2L Engine To Remove:

1. Disconnect the negative battery cable from the battery.
2. Drain the coolant from the engine.
3. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation
   
   
4. Remove the engine coolant temperature (ECT) sensor from the engine.

To Install:

1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
2. Install the engine coolant temperature (ECT) sensor into the engine. Torque the sensor to 12 ft-lb (16 Nm).
3. Connect the engine coolant temperature (ECT) sensor connector.
4. Refill the engine with coolant.
5. Connect the negative battery cable to the battery.

5.3L & 6.0L Engines To Remove:

1. Drain the coolant from the engine.
2. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation
   
   
3. Remove the engine coolant temperature (ECT) sensor from the left cylinder head.

To Install:

1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
2. Install the engine coolant temperature (ECT) sensor into the left cylinder head. Torque the sensor to 15 ft-lb (20 Nm).
3. Connect the engine coolant temperature (ECT) sensor connector.
4. Refill the engine with coolant.

Temperature control sensor is located a)oil sensor on the oil filter b)coolant sensor engine block cover

It's located under the hood, driver side, upper engine area, mounted on rear of engine block behind cyl. head.

The Engine Coolant Temperature (ECT) sensor is mounted in the intake manifold and sends engine temperature information to the ECM. The ECM supplies 5 volts to the coolant temperature sensor circuit. The sensor is a thermistor which changes internal resistance as temperature changes. When the sensor is cold (internal resistance high), the ECM monitors a high signal voltage which it interprets as a cold engine. As the sensor warms (internal resistance low), the ECM monitors a low signal voltage which it interprets as warm engine.
Fig. 1: View of the Engine Coolant Temperature (ECT) sensor Fig. 2: Engine Coolant Temperature (ECT) sensor locationTESTING
See Figures 3 and 4

1. Remove the ECT sensor from the vehicle.
2. Immerse the tip of the sensor in container of water.
3. Connect a digital ohmmeter to the two terminals of the sensor.
4. Using a calibrated thermometer, compare the resistance of the sensor to the temperature of the water. Refer to the engine coolant sensor temperature vs. resistance illustration.
5. Repeat the test at two other temperature points, heating or cooling the water as necessary.
6. If the sensor does not meet specification, it must be replaced.

Fig. 3: Intake Air Temperature (IAT) and Engine Coolant Temperature (ECT) sensor wiring diagram Fig. 4: ECT sensor temperature vs. resistance values