1995 GMC Suburban Logo

Related Topics:

EVA BIGELOW
EVA BIGELOW Posted on Dec 23, 2014
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

What type battery do I use in my keyless entry?

I had put in cr2032 in and now my locks do not work with remote or by manually

Answer This Question

1 Answer

Bill Boyd

Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

  • GMC Master 53,816 Answers
  • Posted on Dec 25, 2014
Bill Boyd
GMC Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

Joined: Jan 04, 2013
Answers
53816
Questions
7
Helped
11950506
Points
172802

Check that it is in the right way round . If so you may have to get the remote reprogrammed to the system as there is no memory for the key fob

5 Related Answers

Anonymous

  • 3 Answers
  • Posted on Apr 06, 2009

SOURCE: Keyless remote entry does not function, panic button does.

This link will take you to very good instructions try it worked for me www.wikihow/program-a-keyless-entry-for-a-chevy-silverado this works on GMC models also.

Ad
Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Apr 08, 2009

SOURCE: Driver 2 Remote Keyless Entry (RKE) not working, Driver 1 is OK

To resynchronize your transmitter, stand close to your vehicle and press and hold the LOCK and UNLOCK buttons on the transmitter at the same time for seven seconds. The door locks should cycle to confirm synchronization. If the locks do not cycle, see your dealer for service.   I hope this works and good luck

Anonymous

  • 45 Answers
  • Posted on May 21, 2009

SOURCE: 99 gmc jimmy sle keyless remote and security issue

Hi: From my experience the security issue is easily solved because hitting the factory key FOB lock button is the only way to activate it, hitting door lock button will not activate it. When installing a remote starter no wires are cut usually, just spliced into which means... make sure that where wires were spliced they are taped. If you have the original factory key FOB use a quarter and pop apart, replace the battery, key FOB should have retained its factory setting if your lucky, if doesn't work go to internet search and find programming procedure. Hope this helps... please rate suggestion...ty

Anonymous

  • 15 Answers
  • Posted on Jun 17, 2009

SOURCE: keyless entry remote quit working. Just purchased

Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Anonymous

  • 2 Answers
  • Posted on May 24, 2010

SOURCE: 2007 gmc yukon denali wont unlock w/ keyfob

Check the buttons.. I have an 06 Grand Prix with the Remote starter on the top and it seems that the conductor on the buttons worn out.. Take the keyfob apart, pull the rubber buttons off the chip, lick your finger and touch the place where the unlock (right side of the fob) would be. That should unlock your doors. I just did it with mine. I would just buy another fob on ebay and change the buttons out.. Hope this works

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

What are the locations of the Remote Control Door Lock Receivers RCDLR in a 2015 Malibu?
According to GM there are 3 components in the RCDLR or RKE remote keyless entry system. My key fobs with new batteries only work standing right next to the car. The range of the key fob dropped at that the same time my TPMS tire pressure monitoring system repair warning came on my dashboard. The problem is that there are 4 different components on the 2015 Malibu. I will provide the GM part numbers for these, if you please tell me where they are and also how to replace them: #13583559 Remote Control Door Lock Receiver #13502554 Antenna #13502551 Ignition Lock Key Transmitter Antenna #13502549 Low Frequency Console Antenna
Read full answer
Jan 31, 2023 • Cars & Trucks
1helpful
1answer

Which fuse powers the power door locks on a 2012 equinox? None of the doors lock or unlock with the fob, battery ok
The Lock's lock from the door switches ? If they do it's not a fuse problem . Which of these does your vehicle have ?
Keyless Entry System Description and Operation (with Accessory 2 Way Remote)
Keyless Entry System Description and Operation (without Accessory 2 Way remote)

The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors/liftgate when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Vehicle locator/Panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Your best bet , take it to a GM dealer .
Read full answer
Jun 06, 2018 • Chevrolet Equinox Cars & Trucks
0helpful
2answers

Changed battery in keyless remote and now doesn't start car or open doors

  • HOW TO - Change the battery and quick fix your car remote ...

    ? 9:32
    https://www.youtube.com/watch?v=KzCXGXCe0oc
    Sep 1, 2011 - Uploaded by tyreeztt
    Also if your remote isn't working with a new battery please check out this ... TO - Change the battery and quick fix your car remote / keyless entry ...

    Remote Key does not lock / unlock doors after battery change ...

    www.6speedonline.com/.../208274-remote-key-does-not-lock-unlock-do...
    Apr 17, 2010 - After I changed the battery, it would no longer lock / unlock the doors. ... I can start the call and all .. its just the door and trunk lock / unlock function that does not seem to work . ... now your fob is learned... the keyless entry goes into a "sleep" mode to preserve the batt.. if u do not use the ... Still don't work .

    how do i reprogram my lock remote to my car? i changed my ...

    www.cargurus.com > Questions > Hyundai > Tiburon

    CarGurusAug 17, 2009 - i change my battery an now my lock an un lock buttons dont work on my remote how o i reprogram it? ... I have a Hyundai 2003 Tiburon, and the followingworked for me, get ... However for a replacement keyless remote fob, you will have to go to ... And no, they don't do it for free (ranges from $30-$50 in my ...

    Top 5 Tips in Fixing a Keyless Remote ' eBay

    www.ebay.com > ... > Safety & Security > Keyless Entry Remote / Fob
    Key fobs that don't permit entry can be a major hassle for drivers, but fortunately, there... Drivers with a bit of basic electronics experience are often able to replace their ...After confirming that a remote is faulty, try replacing its battery. ... like "Jeep Wranglerkeyless remote," to find listings that will work with specific vehicles.

Read full answer
Jan 26, 2016 • 2005 Ford Freestyle
0helpful
1answer

2008 HHR Remote Starter not working
Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Guessing will not fix this .
Read full answer
Jan 12, 2018 • 2006 Chevrolet HHR
0helpful
1answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...
The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM
Read full answer
Apr 12, 2017 • Ford Mustang Cars & Trucks
6helpful
1answer

Keyless remotes not working
Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.
Read full answer
Jun 06, 2010 • 1998 Ford F150 Regular Cab
0helpful
1answer

Keyless entry on honda civic 2006 not working
The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.
Read full answer
May 12, 2009 • 2006 Honda Civic Hybrid
0helpful
2answers

My remote for the keyless entry does not work.
does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back
Read full answer
Mar 22, 2009 • 2004 Lincoln LS
0helpful
3answers

Remote keyless entry not working
dealer only
Read full answer
Nov 13, 2008 • 2001 Honda Civic
0helpful
2answers

Door lock
Make sure the battery on your Keyless Entry remote is a working battery.

If thats not it, it could very well be the actual button on your Keyless Entry remote being faulty. But it could also be a relay in the car aswell. Depending on the cost of a Relay versus the cost of a Keyless Entry remote, I would try to replace either/or and try again, whichever is cheaper. The Relay may be cheaper, but your Key-FOB sounds like it could be the cause.
Read full answer
May 16, 2008 • 1994 Nissan Maxima
Not finding what you are looking for?

View Most Popular

1995 Suburban

  • Cars & Trucks

Related Question

What are the locations of the Remote Control Door Lock Receivers RCDLR in a 2015 Malibu?

  • Cars & Trucks

33 views

Ask a Question

Usually answered in minutes!

Popular Questions

Transmission wont shift into 3rd gear.

1999 GMC Suburban

Symptoms of a bad pick up module on a 1996 GMC

1996 GMC Suburban

Air/Hissing Noise from Brake Pedal

1995 GMC Suburban

99 Yukon - Blower Motor Not Working

1999 GMC Suburban

1999 chevrolet suburban: door panel removal

1999 GMC Suburban

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...