The maintenance required light on my wife's 2004 Hond Pilot is blinking 10 times when she turn on the ignition. It started doing this after I put in new plugs and an oil change. What does it mean. I already know how to reset it.

Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.

1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
2. Hold the button for at least 10 seconds, until the indicator resets.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:

1. Turn the ignition switch to the ON (II) position.
2. Press the select/reset knob repeatedly until the engine oil life is displayed.
3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.

All information is taken from the Honda Pilot owners manual.

If you take your civic into a Honda dealer for regular maintenance they should reset it for you. Even most Lube shops do as well. But if you do your own vehicle services like oil changes (which is what that light is there for) then here's how you can reset it.

1. put your key in the ignition but do NOT turn it.
2. press and hold the Odometer/Trip button.
3. while holding the Odometer/Trip button, turn the key to the ON position but do NOT start the engine.
4. As you hold the Odometer/Trip button, after about 10-15 seconds the Maintenance required light should turn itself off.
5. Once the Maintenance required light is off, turn the key into the off position then release the Odometer/Trip button.

That should do it. Hope this helps

• With the ignition switch OFF, press and hold the select/reset button
• Turn the ignition switch ON, and hold the button more than 10 seconds.

With the ignition off, press and hold the odometer reset button in. While holding it in turn the ignition switch on but do not start the engine. After around 5-10 seconds the maintenance required light will reset.

First to check with OBD codes reader, this is one advise to fault; when you have this number (code) the clues for solve the problem are more.

Try it, comment and rated this.

Ive never heard of a timing belt light, but there is a maintenance light that can be reset. Here the procedure:

To reset the maintenance reminder light: Turn the ignition switch to the "ON" position. Set the odometer/trip display to the odometer (ODO) mode. Turn the ignition switch off. Depress and hold the trip meter reset button while turning the ignition switch to the on position. The maintenance reminder light will, illuminate for 3 seconds, blink for 2 seconds, illuminate solid for 1 second and then turn off. Release the trip meter reset button. Turn the ignition switch to the off position. Turn the ignition switch to the on position. Confirm that the maintenance light goes out.
Let me know if this helped you out!

1. Turn off the engine. The car should not be running when performing these steps.
2. Press and hold the select/reset knob. This knob is located on the instrument panel. It will be sticking out on the bottom right of instrument panel. It's the same knob that is used to reset the trip mileage or change what is displayed in the mileage/temperature box.
3.While holding the knob, turn the ignition switch (the key) to on (II) position. Continue holding the knob for approximately 10 seconds. The MAINT REQ'D light should turn off.

To reset maintenance light on this honda, using reset switch on dash in cluster(close to trip reset). Here is procedure HOLD DOWN RESET BUTTON while holding down, turn ignition to first position ACC/(first click.) Hold button for 30 seconds.Keep holding down button and turn ignition to ON position for an additional 30 section maintenance light should go off. Start vehicle and it should be good. Good luck and thanks for using FIX YA.

to reset the the light , turn ignition switch to off position , press and hold the select/reset trip button , while holding the button turn ignition switch to the on position , with the engine off , continue to hold the reset button for about 10 seconds until indicator resets , your done.
you will see like 5 dashs blink then 4 then 3 then 2 then 1 then all flash . problem solved .

Happens all the time to me. I trigger the Theft System by accident then the car won't start.  try this: Put the key in the ignition. Turn it to the "on" setting,but don't try to start the engine. Let it sit for 10 minutes until the Security light stops blinking and turns off. Take the key out and restart. Warning - don't have your lights, radio,etc on while you do this or the battery may die.