1993 Jeep Grand Cherokee Logo

Related Topics:

A
Anonymous Posted on May 30, 2014

How to tell when a 93 grand cherokee governor pressure sensor goes bad

Jeep runs fine on the highway but after getting into start and stop traffic and sitting at red lights it wont shift out of first gear unless it sits for awhile turned off. sometimes it doesnt want to shift from second to third.

5 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Feb 17, 2009

SOURCE: Where is Neutral safty sensor switch located on Grand Cherokee

OK then the switch is part of the gear selector switch on the side of the trans where the shift linkage hooks up. here is a picture and part number.
ACDELCO Part # C2241 $233.89

673ffc9.jpg

Ad

Anonymous

  • 1 Answer
  • Posted on Mar 07, 2009

SOURCE: Transmission problem

I had a shifting problem. The car would start in the wrong gear and shift at wrong times. I repaced the governor postion sensor and tranny fluid and the problem has been fixed for several years. Did you replace the tranny fluid?

Anonymous

  • 667 Answers
  • Posted on Mar 23, 2009

SOURCE: 93 jeep 4.0 not starting

check the ignition coil pick up

Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Jul 01, 2009

SOURCE: Oil pressure gauge drops after running and sitting still

The Oil pressure sensor seams to have gone bad and needs to be replaced soon as possible as they tend to leak oil soon after. There common to go bad and start with that since it's easier then replacing the oil pump, but if you don't hear any ticking from the engine and you have good pressure when the engine is cold then it's the sensor. 
The 4 cylinder oil pressure switch is located below the A/C compressor. It is a single wire connection with a gray/yellow striped wire. 

The 6 cylinder oil pressure switch is located on the passenger side rear of the block. It is a single wire connection with a gray/yellow striped wire. 

Good luck and hope this helps. 

Anonymous

  • 295 Answers
  • Posted on Jul 20, 2009

SOURCE: 2005 Jeep Grand Cherokee Shifting Problems

Check the Trans fluid level with it running and at operating temperature. Jeep NAG1 transmissions are known to have the input electric seal leak trans fluid. Not an exspensive fix add Mopar ATF4 and then relace the guild seal.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

2001 jeep GC p1756 error code

get your jeep to a transmission shop either the pump is going out or the governor pressure valve is bad so the solenoid pack may need to be replaced.
0helpful
1answer

Code p1762 govenor pressue sensor offset volts

P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed
1helpful
2answers

93' Grand Cherokee, dont start, no spark,no gas preassure

my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith
1helpful
1answer

Oil Pressure Always Runs High - 2002 Grand Jeep Cherokee

If your oil pressure is running in the red this would indicate too much oil in the system. You should have your oil changed and refilled soon or you run the risk of burning out the oil pump. At idle your pressure should be just over a quarter of what your gauge has. At highway speed it should not exceed 3/4 of the gauge unless your going in excess of 100 MPH. Change the oil and filter and your vehicle should be fine.
1helpful
1answer

93 Jeep Grand Cherokee Won't start

The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.
0helpful
1answer

93 jeep 4.0 not starting

check the ignition coil pick up
2helpful
1answer

Transmission problem

I had a shifting problem. The car would start in the wrong gear and shift at wrong times. I repaced the governor postion sensor and tranny fluid and the problem has been fixed for several years. Did you replace the tranny fluid?
11helpful
1answer

2001 jeep grand cherokee transmission revving-codes p1757, p1762

P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed
0helpful
1answer

93 grand cherokee jeep running rough

There is a sensor on the top of the transmission housing that if it goes bad can give you these sypmtons. It's called the crank sensor.
0helpful
1answer

93 Jeep Grand Cherokee Laredo

Could be a sensor.I'm thinking more along the lines of a fuel pump or fuel filter.If the fuel pump is going bad..similar symptoms.Would be advisable to install a pressure gauge at the engine,and check fuel pressure when it's acting up.
Not finding what you are looking for?

98 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...