VW Jetta torque setting and hub nut size????

Remove brake components, remove centre cover to expose securing nut, remove nut and using a 3 jaw puller remove the bearing and hub. The inner race will remain on the spindle and will need to be cut off being carefully not to cut the spindle. I use a cutting torch to achieve this. ER the spindle cool befor installing the new bearing/hub assy. Don't forget to torque the nut to spec. I can't remember offhand what it is but if you over tighten it the braring life will be reduced. Also use a new nut as they are one time use and may loosen over time if reused.
Good luck!

33ft/lb, 44ft/lb, plus 1/4 turn

Try this image here, this may be what you need.


http://www.flickr.com/photos/zehnuss-vw-projekt/5430899459/sizes/l/in/photostream/

how to replace diff bearing 2002 vw jetta tdi deisel

Very nice to know that somebody care of his car.I understood that this is 1.9 TDI JETTA in124000 miles.To avoid problems in the future you have to change gearbox oil by recommended from a manufacturer.Second-Check all wheel bearings/rear ones/ for noise.Also make suspension test. any way you have to visit vw workshop for full diagnostic of the JETTA

Replace the Engine Coolant Temperature (ECT) sensor. ECT sensor is placed in the right back side of the cylinder head on 2002 VW Jetta 1.9 TDI. See picture below:



Please do rate my response. Thanks!

1993-2005 Volkswagen Jetta, Golf, GTI, Cabrio (A3-A4) Hatchback & Sedan Workshop Repair Service Manual - 350MB PDF

1993 2005 Volkswagen Jetta Golf GTI Cabrio A3 A4 Hatchback Sedan...

This is a COMPLETE Service and Repair Manual for your 1993 1994 1955 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 VW Jetta, Golf, GTI, Cabrio (1.8L turbo, 1.9L TDI and PD diesel 2.0L gasoline, 2.8 LVR6) (A3, A4 Platform) Hatchback & Sedan. It covers every single detail. All models, and all engines are included.

This QUALITY manual is 100 percents COMPLETE and INTACT, no MISSING/CORRUPT pages/sections to freak you out! Detailed illustrations, exploded diagrams, drawings and photos guide you through every service repair procedure. This manual can be viewed on any computer, as well as zoomed and printed. All repair procedures are covered A-Z. This manual for VW Jetta, Golf, GTI, Cabrio makes any repair job easy to do with very easy to follow step-by-step instructions & pictures on all areas of repair.

1993 1994 1955 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 VW Jetta, Golf, GTI, Cabrio (1.8L turbo, 1.9L TDI and PD diesel 2.0L gasoline, 2.8 LVR6) (A3, A4 Platform) Hatchback & Sedan
===========
Format: PDF
System: All Versions of Windows, Mac, iOS, BB, Android, etc..
Requirements: PDF Reader.
Printable: Yes

TABLE OF CONTENT (example)

GENERAL INFORMATION *

ENGINE *
engine mechanical
engine lubrication system
engine cooling system
engine control system
fuel system
exhaust system

TRANSMISSION/TRANSAXLE *
clutch
manual transaxle
automatic transaxle

DRIVELINE/AXLE *
front axle
rear axle

SUSPENSION *
front suspension
rear suspension
road wheels & tyres

BRAKES *
brake system
parking brake system
brake control system

STEERING *
power steering system
steering system

RESTRAINTS *
seat belts
supplemental restraint system (srs)

BODY *
body, lock & security system
glasses, window system & mirrors
roof
exterior & Interior
Instrumental panel
seat

AIR CONDITIONER *
air conditioner system

ELECTRICAL *
wiring diagrams
starting & charging system
lighting system
driver information system
wiper, washer & horn
body control system
lan system
audio visual, navigation & telephone system
auto cruise control system
power supply, ground & circuit elements

MAINTENANCE *
maintenance

INDEX *
alphabetical Index

1993 1994 1955 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 VW Jetta, Golf, GTI, Cabrio (1.8L turbo, 1.9L TDI and PD diesel 2.0L gasoline, 2.8 LVR6) (A3, A4 Platform) Hatchback & Sedan

Temporarly torque the axle nut to 87 in.lb., while turning the brake drum by hand. Then loosen the nut slightly. Tighten the axle nut again, slowly and in small increments while turning the wheel, until the thrust washer can just barely be moved back and forth with a light push from the tip of a screwdriver.

take off rear hub u have a inner and outter bearing ..change bearing dont forget to pack new bearing well with a GAA Bearing Grease...and install wheel and tighten middle nut till wheel is tight...then back it off enough that wheel turn but not too freely about half a turn back....GL

2 options:  take it to a shop the bearing comes compresed with the hub. you need a machine to do that or buy the hub with the bearing...I say shop its less expensive. GOOD LUCK!