P0336 Code 99 Malibu, 3.1 engine. Engine light on. Code: P0336. When I erase the code the car runs without engine light on for one trip. When I stop and start again the engine light re-appears. The car seems to run ok although I believe it is using quite a bit of gas. Any ideas? Thanks Terry

Who replaced the sensor ? You or a repair shop ? The DTC P0336 does not say to replace a sensor . You do not have access to the diagnostic trouble code diagnostic's . Your best bet ,take it to a qualified repair shop .
DTC P0336: Crankshaft Position (CKP) Sensor Performance
CKP Sensor Signal Circuit
P0335
P0335
P0335
P0336

P0336
• The ECM detects that the engine is running, but receives less than 51 or more than 65 CKP sensor pulses each engine revolution for 8 of 10 engine revolutions.
• The ECM detects that the engine is running, but more than 19 resyncs occur within 25 seconds.
• The ECM detects that the engine has been running, but the crankshaft does not sync for 0.4 second.

P0336 Crankshaft Position Sensor Range/Performance

www.obd-codes.com/p0336
Detailed information on troubleshooting and repairing a P0336 DTC code which has to do ... This diagnostic trouble code (DTC) is a generic powertrain code.

take vechicle by auto zone they will code scan it free see what causing check engine light turn on.if you replace sensor you need auto zone to erase code so check engine light stop turning on.

which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

well lets start with warming up the engine. so run it for a while. stop the engine and unplug the throttle position sensor. restart the engine and rev it 2000-3000 rpms 2 or 3 minutes under no load (such as lights, blower motor, a/c and so on) and then run it at idle speed. check timing at idle using timing light and set it to 20+/-2 BTDC.after adjustment shut the truck off and replug the throtle position sensor back. this will however turn your "service engine soon" light on, because you have unpluged the sensor and ran the truck. you will need to erase the ecm memory/reset it/get code reader and erase code.
thats how you doit without nissan scanner aka CONSULT2.

You may have a leak in the EVP system, causing the light to stay on. It would help if you had erased the code with a code reader that allows you to erase codes in the PCM. Make sure the cap is tight and clicks at least 3 times, drive the vehicle a few miles. Stop the car, turn off the engine, then restart and drive. it may take a few "good" trips to be recognized by the engines computer borfore it turns off. If your comfortable with removing the NEGATVE SIDE battery cable for 30 seconds, then reconnecting it and make sure it is clean and tight, you can try it to see if this helps turn off the light faster. If not, you may have another issue regarding the EVAP system.

Its a tough one without knowing what the Check engine code is.. A trip by your local Autozone, Advance or nearby parts store should be able to get this info for you. These stores will retrieve the code for you... but they usually will not erase it.. hope this helps..

P0336 means Crankshaft Position Sensor A Circuit Range/Performance. Try replacing the crank sensor next.

http://www.check-engine-light.com

P1665 Evap vent solenoid control circuit

p0130 is an oxygen sensor code.
p0340 is your camshaft position sensor code
p0336 is your crankshaft position sensor code

as far as the p0130 code those usually are what i call neglected sensors that do not get replaced when they should be. this sensor is expensive but worth the money as it will help on fuel mileage.

on to the camshaft position sensor, i would start here with this. replace that sensor and when you are replacing it, inspect the sensor and make sure the electrical wires going into it are in good shape. after replacing those 2 sensors, go to a parts store who can erase your codes to turn the light off and then let us know if it comes back on and then we will go from there on the repair.