How to replace fule injectors on 2006 srx

SOURCE: 2003 cadillac deville rough idle with blinking ses

have the head gasket checked,pretty common on these

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

http://wiki.answers.com/Q/How_to_change_the_Cadillac_SRX_Front_Tun_Signal_Bulb

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

SOURCE: Check engine light was on. OBD II scan said both

The pre cat sensors running lean does not mean they need to be replaced. They are are detecting a symptom. You need to know why.

If you are using a basic scantool (code only) you need to look up the P0000 code.
I thought this an odd code. I looked it up in my Autotap unit and it does not exist. The lowest # P (powertrain) code I have listed is P0016.

A regular scan tool, won't scan transmission or body codes, mu Auto tap doesn't either. You need a Tech 2 from the dealer for transmission codes.

First some history. The first O2 sensor was introduced in 1976 on a Volvo. California vehicles got them next in 1980, then federal emission laws made O2 sensors virtually mandatory on all cars and light trucks built since 1981. And now that OBD-II regulations are here (1996 and newer vehicles), most vehicles now have multiple O2 sensors, some as many as four!
The O2 sensor is mounted in the exhaust manifold to monitor how much unburned oxygen is in the exhaust. The signal from the O2 sensor tells the computer if the fuel mixture is burning rich (less oxygen) or lean (more oxygen).
A lot of factors affect the richness or leanness of the fuel mixture, including air temperature, engine coolant temperature, barometric pressure, throttle position, air flow and engine load. Other sensors monitor these factors too, but the O2 sensor is the master monitor for what's happening with the fuel mixture. Problems with the O2 sensor can throw the whole system out of whack.
The computer uses the oxygen sensor's input to fine tune the fuel mixture for the best balance of power, economy and emissions. The engineering term for this type of operation is "closed loop" because the computer is using the O2 sensor's input to adjust the fuel mixture. The result is a constant flip-flop back and forth from rich to lean which helps the catalytic converter operate at its best and keeps the average fuel mixture in proper balance to minimize emissions. It's a complicated setup but it works.
If no signal is received from the O2 sensor, like when a cold engine is first started (more on that in a minute) or the 02 sensor fails, the computer orders a steady, rich fuel mixture. This is referred to as "open loop" operation because no input is used from the O2 sensor to fine tune the fuel mixture. If the engine fails to go into closed loop when the O2 sensor reaches operating temperature, or drops out of closed loop because the O2 sensor's signal is lost, the engine will run too rich causing an increase in fuel consumption and emissions. As you might have guessed, that will set a code and turn on your check engine light.
How does it work? The O2 sensor produces a voltage once it gets hot. The sensor compares how much oxygen is in the exhaust to the oxygen in outside air. The greater the difference, the higher the voltage reading.
If you ever replace an O2 sensor (and if you're a DIY'er this is something you will do eventually), its important to remember that the O2 sensor needs to "breath" outside air to work. So don't put any grease on the sensor because it could block this air flow.
An oxygen sensor will typically generate up to about 0.9 volts when the fuel mixture is rich and there is little unburned oxygen left in the exhaust. When the mixture is lean, the sensor's output voltage will drop down to about 0.1 volts. When the air/fuel mixture is balanced or at the equilibrium point of about 14.7 to 1, the sensor will read around 0.45 volts.
When the computer reads a rich signal from the O2 sensor it leans the fuel mixture to reduce the sensor's reading. When the O2 sensor reading goes lean the computer reverses again making the fuel mixture go rich. This constant flip-flopping back and forth of the fuel mixture occurs anywhere from 2 to 7 times a second at 2500 rpm on OBDII vehicles, depending on what type of fuel injection system they have.
The oxygen sensor must be hot (about 600 degrees or higher) before it will start to generate a voltage signal. Many oxygen sensors have a small heating element inside to help them reach operating temperature more quickly.
Ok – that was a lot of info on what they do and how they work. The next thing to know is that trouble codes relating to O2 sensors are very common. But you really need investigate further before replacing an O2 sensor just because you got that trouble code. Armed with the information above on how often the O2 sensor "flips" back and forth and AutoTap or another scantool that allows you to monitor O2 sensor voltage, you can be certain whether the O2 sensor itself is really the problem. These sensors can be pricey, so don't just replace them the first time you see that trouble code!

The O2 sensors are expensive, diagnose what really is going on.

SOURCE: how to replace rear shocks on a 2006 cadillac srx

Your car should have different shocks from most cars, with the magnetic, electrical charge viscosity change. Be sure that the shocks are actually not functioning correctly.