1996 GMC Yukon Logo

Related Topics:

A
Anonymous Posted on Aug 23, 2017

1996 GMC Yukon will not start after hearing intermittent clicking noise while running

All gages were normal when vehicle was operating but intermittment clicking noise was heard in area in front of driver's side of vehicle. No previous problems with starter. Upon attemting to start the engine there is no turnover and all electrical power goes off. After waiting several minutes the electrical system seems to reset and electrical power is restored to lights, etc.

1 Answer

Joe Stanton

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

  • GMC Master 1,154 Answers
  • Posted on Aug 23, 2017
Joe Stanton
GMC Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

Joined: Apr 09, 2013
Answers
1154
Questions
5
Helped
315669
Points
3584

Sounds like you lost the serpentine belt, which runs the alternator. When you heard the ticking sound, did you notice if the battery light came on, Check the belt and fully charge the battery. Do not jump a dead battery. Wear safety glasses when servicing a battery, an explosion and acid hazard exist

2 Related Answers

Terry Long

  • 241 Answers
  • Posted on Jan 27, 2011

SOURCE: The 2.9 4 cyl. engine in my 04 GMC Canyon dies

you probably have corrosion in the power train control module and connector.it is located under the hood on the passenger side on the fire wall.remove the connectors from the module and clean the connectors and module with a soft brush and spray them with electrical cleaner.i have seen this problem before.

Ad

Anonymous

  • 3489 Answers
  • Posted on Aug 01, 2011

SOURCE: 97 GMC Sierra starter engagement

This sounds primarily like a starter on it's way out. The next time the starter will not engage the first time, have someone else hold the key into the start position and you tap the starter with a hammer and if it engages, replace your starter. Let me know if you need instructions on how to do so.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

1999 GMC Yukon SLT 4x4 What is making it loose power at take off and sometime popping noise? Could it be timing?

Where do you hear this popping noise ? Intake manifold ? or front of engine ? How does the vehicle run at higher rpm's ?
0helpful
2answers

High Pitched Whine

A high pitched whine like that indicates a bad bearing. Water pump, power steering pump, accessory belt slipping, alternator bearing, or in the worst case scenerio, Transmission pump.
0helpful
1answer

2001 GMC Yukon - Clicking noise from dash/steering column are. Starts clicking at 10mph and gets worse the faster you go. Touching the shift lever at all changes the click frequency or stops it completely...

I was having a clicking noise from a actuator under the dash of my car, it was a blend actuator.. Years ago they used cable then vacuum hose and now a lot of vehicle us actuators (motor driven gate) to open and close the vents, A/C and heater ducts. I do not know for sure that is your problem but when mine went bad I would get a clicking noise sometimes it click for a few seconds after I turned the car off. Just a thought.
1helpful
1answer

My 2003 Yukon Denali has an intermittent problem with the passenger door window. It sometimes will not operate with either control. I can hear electrical clicking when either switch is activated. ...

the door window motor might be weak or has stoped working. my 2003 pass window motor went also, all others work fine still but the drivers is starting to get weak now, i tried to lube the cable and sliders but that did nothing. Replaced pass with a $60.00 used and its great.
0helpful
2answers

How do you use an obd2 scanner to time a 1996 gmc yukon w/350, and which make and model scanner should i get?

It will not time the vehicle,it is already programmed into the vehicles e c m .
2helpful
1answer

1996 gmc yukon occasionaly my gear shifter gets stuck in park

do you have to put your foot on the break in this vehicle to get it out of park normally if so you may need a new brake light switch as it may have a intermittent fault and not be sending the right signal to get the stick out of park
0helpful
1answer

Dash Gages

bad altenater or short in wiring
0helpful
1answer
Not finding what you are looking for?

110 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...