1998 Isuzu Trooper Logo

Related Topics:

A
Anonymous Posted on Mar 22, 2012

EGR VALVE LOCATION 4JX1 ISUZU TROOPER

5 Related Answers

stevenhurc

Steve Hurc

  • 459 Answers
  • Posted on Nov 02, 2009

SOURCE: where is the location of the egr valve on a 2001

on petrol V6 engine its right rear side of inlet manifold(left side when looking into engine bay) see pics. below
diesel its on inlet manifold left side middle section of manifold

eb59265.jpg
2736ba4.jpg

Ad
simontricket

Simon

  • 235 Answers
  • Posted on Feb 08, 2010

SOURCE: isuzu tropper 4jx1

You have no injection pump ,each injector does that job .
You have a faulty rail oil pressure sensor I think ,read my tips to test this sensor .

Anonymous

  • 15935 Answers
  • Posted on Jul 03, 2009

SOURCE: where is the egr valve for a 1999 isuzu trooper?

The EGR valve is a cylindrical unit above the engine. It would be behind the throttle body.
It will have a cable connected to it. Unplug the cable.
There two bolts. Simply remove.
An that is all there is to it.
Simply put the new EGR valve in its place, screw in the bolts and reconnect the cable.
Make sure to see a gasket. The gasket can stick to either the EGR valve or the throttle body. It does come off easily but since it is metallic, it looks like it part of the throttle/egr valve.

74cc5a2.jpgThanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

kel1guy2002

Kelly

  • 3740 Answers
  • Posted on Jan 20, 2010

SOURCE: How to clean EGR valve passages in 1993 Isuzu Trooper DOHC V6

You have to the EGR valve (sometimes the Intake manifold to EGR Vlalve line also). After you remove it take a drill bit the about 20 % smaller than the actual hole of the outlet side and rotate the drill bit with your hand to dig out the carbon. Aditionally the line coming from the intake manifold to the EGR valve will clog near the connection to the EGR valve. I use either a single piece of copper wire or the wire that you would use to tie ribar together to clean the line. When your done cleaning take a piece of vacuum line and connect it to the diaphram side and **** on it... then plug the line well with your thumb. Grasp the valve and blow thru it... Air should blow thru it freely. Remove your thumb from the vacuum line and try blowing again.. No air should pass thru the valve.
Then reinstall the valve and start the vehicle with the vacuum line disconnected (but blocked off) Use another piece of vacuum line connected to the diaphram again and **** on the line.. The vehicle should die or run really bad. If it does this then you cleaned it correctly.

tuyen bui

  • 1025 Answers
  • Posted on Feb 25, 2010

SOURCE: egr valve location isuzu axiom

right rear of the engine on the top of intake manifold next to fire wall. long cylinder looking with a connector on top

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
2answers

What is crank position sensor on Isuzu trooper 2002 3tdi

What is? It tells the ECU what position the crank is in to control timing.
0helpful
1answer

Modulator valve location

to what? transmission or is the EGR mod or?
what year, trooper.
and what engine.

modulator means zero.
the injectors are modulators, the ISC is, and many other parts.
the car has systems. name just one,
2.0 L G200 I4 (UBS13)
2.3 L 4ZD1 I4 (UBS16)
2.6 L 4ZE1 I4(UBS17)
2.2 L C223 diesel/turbodiesel I4(UBS52)
2.8 L 4JB1 diesel I4
2.8 L 4JB1-T turbodiesel I4
2.0 L G200 I4 (UBS13)
2.8 L LH7 V6
2.8 L LL2 V6
3.2 L 6VD1 SOHC V6
3.2 L 6VD1 DOHC V6
3.5 L 6VE1 DOHC V6
3.0 L 4JX1 TD I4
3.1 L 4JG2 TD I4 and many transmission, the body is a shell, the drive line is all optional.
0helpful
1answer

I cannot start my isuzu bighorn w/4jx1 engine. we already changed the turbo but still it emits too much smoke in the exhaust and after a while the engine goes wild and we cannot turn it off in the ign

Its a diesel and its running away so do not try to start till you do the following and yes i know i will be amolished for being a cowboy by the other experts but what you do is to make a gasket for the EGR valve from a coca cola can and seal it off if you dont it may run away and blow itself to pieces .If you do this then it run as normal as the older trucks never had these thing fitted and they all run ok in my day ,exactly whats wron i couldnt tell you without my head under the bonnet but do as i say and it run perfectly
1helpful
1answer

Where is the location of camshaft sensor 1998 isuzu trooper

if its diesel 4JX1 its in top cam belt cover cant miss it, sensor is very clearly visible.
if its petrol V6 (6VD1 or 6VE1) its in left head at rear behind inlet manifold
these pictures are for petrol V6, Jackaroo(Trooper) and Holden Rodeo are the same.

stevenhurc_21.jpg



stevenhurc_22.jpg
3helpful
1answer

I have a code P1860 and code P0405 in my 2001 isuzu trooper

Code p0405 is for faulty EGR vave od some of the pipe/lines going in or out of EGR valve/system hase broke, leaks or fall of. Or egr valve is dirty and stuck. Check EGR valvle!
20helpful
2answers

Isuzu tropper 4jx1

You have no injection pump ,each injector does that job .
You have a faulty rail oil pressure sensor I think ,read my tips to test this sensor .
7helpful
1answer

Where is the location of the egr valve on a 2001 isuzu trooper

on petrol V6 engine its right rear side of inlet manifold(left side when looking into engine bay) see pics. below
diesel its on inlet manifold left side middle section of manifold

eb59265.jpg
2736ba4.jpg
Not finding what you are looking for?

851 views

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...