20 Most Recent 2006 Honda CR-V SE Questions & Answers

need to notify dealer for code need vin and proof of id --also have vehicle scanned usually radio code needed when battery replaced or went dead but some people selling a used can with a bunch of check engine codes will clear them by disconnecting battery

that vibration means that your tires are out of balance. if they still have good life in them, you should have them balanced.

sounds like you need a new switch or you may have a loose wire in the connector at the switch. try taking the switch from the other side and see if that fixes it then you know.

Hi, One of two possibilities, a front wheel out of ballance or a slight wear in a tie rod end.

Possible causes are as follows, I suspect you have an intake air/vacuum leak or a faulty MAF sensor. - Intake air leaks - Faulty front heated oxygen sensor - Ignition misfiring - Faulty fuel injectors - Exhaust gas leaks - Incorrect fuel pressure - Lack of fuel - Faulty Mass Air Flow (MAF) sensor - Incorrect Positive Crankcase Ventilation (PCV) hose connection Read more: http://engine-codes.com/p0171_honda.html#ixzz2wugiVinS

Hot glue a dent puller button to the top of it. https://www.crvownersclub.com/threads/how-do-i-replace-the-starter-cut-relay-on-a-gen-3.222537/ https://www.google.com/search?q=2014+Honda+CRV+replace+the+starter+relay ..

On a V6 engine, bank 1 is on the drivers side or the bank closest to the firewall. Sensor 1 is the one in the exhaust manifold BEFORE the catalytic converter and sensor 2 is just after in the cat on the way to the tail pipe. On a 4 cylinder engine, there are only two sensors, before (1) and (2) after the Cat. https://www.google.com/search?q=1998+honda+crv+oxygen+sensor+Bank+1+Sensor+2+location Buy Denso OEM (original equipment manufacturer) sensors, don't go cheap on Mexico of China copies. https://www.google.com/search?q=1998+honda+crv+oxygen+sensor ..

It could be so many things. You really need an auto electrician with a Pro grade scan tool computer to check for Diagnostic Trouble Codes. It could be fuel pump or any one of the sensors. It could even be a broken camshaft valve timing belt and it is an interference engine. https://www.google.com/search?q=mobile+auto+electrician+near+me Between 1997 and 2001 Honda CRV was equipped with a timing belt under the hood. However, starting in the 2002 model year, Honda swapped out the timing belt in favour of the much more durable timing chain. To this day the CRV is still made with a timing chain. Dec 15, 2020

Does the Honda CRV Have a Timing Belt or Chain?

IS MY 1997 HONDA CR-V AN INTERFRE OR NON- ...

JustAnswer https://www.justanswer.com > Honda Questions Feb 16, 2012 - Hello I'm Paul and I will help you with an Answer to your Question. this is an interference engine. depending on the speed the engine was ... ..

Question edited for clarity 'hinda' to Honda not 'Hindra', 'crv' in CAPS. Question moved to model category. There are only 3 ways to get the code. Two are free. https://www.fixya.com/support/r29874205-need_vehicle_radio_code ..

You have to clear the ABS Sensor code with a scan tool. Any garage or Autozone will do for free.

Question edited for clarity. Question moved to model category. You have parasitic draw, but disconnecting the fuse box is not the way to find it. This is https://www.fixya.com/cars/r29903527-parasitic_draw_car_batteries Repair manual https://www.google.com/search?q=2013+honda+crv+repair+manual+pdf Best Plan here https://www.google.com/search?q=mobile+auto+electrician+near+me ..

Question re-written for clarity, and 'hobda' to Honda. Question moved to model category. You say it is not locking down securely. So you press in down to lock and it doesn't. That is just a simple adjustment fix, normally you move the securing hook a little closer to the lock. But you also say it seems to be locking and unlocking via the fob. That is an electronics issue. It might just be a bad contact on the solenoid, or it is electronic via the whole electronic door locking system. For that you need an auto electrician. https://www.google.com/search?q=auto+electrician+near+me ..

The OBD-II error code P1399 and P0141 for a Honda CRV 1999 are as follows: P1399 - This code indicates that there is a problem with the misfire detection system in the vehicle. This code is often accompanied by other codes that indicate which specific cylinder is misfiring. Causes of this code could include a faulty ignition system, a clogged fuel injector, or a problem with the engine control module (ECM). P0141 - This code indicates a malfunction in the oxygen sensor located on Bank 1, Sensor 2. This sensor measures the oxygen content in the exhaust gas after it has passed through the catalytic converter. Causes of this code could include a faulty sensor, a damaged sensor wiring harness, or a problem with the vehicle's computer. It is recommended that you have a certified mechanic diagnose and repair these issues to ensure proper operation of your vehicle.

27 ft lbs https://www.instructables.com/Replacing-an-Outside-Tie-Rod-on-a-Honda-CRV/

Question edited for clarity and throw in a few Caps. Question moved from Cell Phones to Car Model. https://www.google.com/search?q=2007+honda+crv+unlock+hands+free+bluetooth ..

Replace the suspension bushes on the suspension arm/s. Replace the bushes on the control arms and have a rear wheel alignment done.