X-10 Answered Questions & Fixed Issues

Yes, you need X10-compatible control modules for any device you want to add. The modules plug into the wall outlet, then the device you want to control plugs into the module. From what I read, the control signals are sent through the power lines to the respective module. Read the manual to see how to reference a controller button to a particular module.

just move the mouse over the picture in the corner and hold down left mouse button and drag the corner inwards and picture will resize.

http://www.thex10shop.com/product/x10-powerhouse-brand-extra-re549-powermid-receiver-pm5900 http://kbase.x10.com/wiki/RE549#Specifications http://forums.x10.com/index.php?board=10.0 http://kbase.x10.com/index.php?title=Special%3ASearch&profile=default&search=RE549&fulltext=Search If you need further help, I’m available over the phone at https://www.6ya.com/expert/ron_a476a70a75690d24

They both have to be set to the same House Code and Unit Code

I KNOW THIS IS NOT A FIX, BUT I HAVE HAD THEM JUST QUIT, USUALLY AFTER A THUNDER STORM. THEY ARE STILL AVAILABLE. Do a search on dogpile or google and you will find them http://www.ebay.com/itm/like/281301991680?item=281301991680&lgeo=1&vectorid=229466

The IN51A, IN53A, VK75A & VR36A, will be a great thing, but what is it? I can't read minds, so I need more details.

DELTON X10. Asking me code previously every time I put 0000 work now need additional code which I lost the book. How I can pair now?

It seems to be on a 3-way switch that has the lights on now. If another switch is turning the light on and off. Heres the manual for 3-way installation.

You will need to login to the router and change its configuration. Usually routers have a default IP address of 192.168.1.1 or 192.168.0.1. You can access it through a web browser by typing in that IP address. The default login is usually user:admin password:admin.

Here you go If you need further help, I’m available over the phone at https://www.6ya.com/expert/chad_70dccdc9090b1a75

Did you ever get the schematic for the x10 barking dog? I need one now.

I've dropped a lot of phones and other devices in water! No feeling quite like it :(Maybe people will advice against this, but I take the hose to my vacuum and (with the batter out) vacuum every inch of my devices. Another tip that has worked is to put the device into ziploc bag of white rice for a day or so. It'll absorb any water that is still locked inside. Hope it works for you!

go to www.fitness.manualsonline.com or www.remotecodelist.comand download the codes + instruction manuals.God bless you

PLW01 has 2 wires: Black wire connects to Hot and Blue wire connects to Load wire.
http://lib.store.yahoo.net/lib/aaaremotes/PLW01.pdf
Remove PLW01 and you have Hot and Load wires.
Standard light switch has two brass colored screws, and one green ground screw.
Connect either wire to either brass screw.
Connect bare ground wire to green screw.

First, what type of NV do have, manufacture it, what wrong with it, what do you want to make????stewbison

Sounds like one or more of the ignition coils are bad or going bad. that would be the first thing I would check.

The simplest way is to email them. A picture message will allow you to send to a email just put your email in where it asks for a phone number.

pull and turn side to side as these are called backstab connectors and theyre internally spring loaded

Hi, kindly get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay__45f7h

The dial with the letters is for setting the "house code". The dial with the numbers assigns a number for each controled device. If your neighbor's house code is the same as yours it is possible that their controller is tuning on your light. Change your house code to another number. Remember that all controllers and controlled devices must be on the same house code to work, so you have to change the house code on the remote also. If you don't want the remote to work just set it to a house code letter that is not being used by anything else. If you don't want the remote to work just for that device, just change the device number.