Quorum Popular Questions, Answers, Tips & Manuals

There are places that sell the whole thing. Just a remote wont be available and you will have to replace the receiver in the fan unit.

-one has a tiny screw on each side of the clip-on that's on rear of the alarm--for that one just remove the 2 tiny screws, carefully remove the back side and the rubber sealer. another comes WITHOUT the 2 tiny screws--merely take small flat end of screwdriver and pry off

What's the problem? If you need a manual call Quorum @1-800-443-4626

If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the relative post easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls.

With the power off, inspect the socket and see if the contacts have been pressed down. You can bend them back up slightly using a small tool. Make sure you do not handle the halogen bulb with bare hands/fingers. The oils in your hands will case the bulbs to fail. Use a cloth when installing a bulb.

Call Quorum at 1-800-443-4626

You need a new remote receiver.

Your best option maybe to contact Quorum International directly and provide the details of the problem including model number of your fans. Quorum International manufacturer of designer coordinated lighting...

Pull chains are pretty generic; pull it apart and replace

first of all if you bought a switch at a store, just because it looks the same on the outside doesn't mean it's the same on the inside. I can tell you that the black wire usually goes into the L. If you can't find the correct switch contact me at. [email protected]

It was an add-on remote so it really depends on the receiver. Locate the receiver, probably in the canopy cover at the ceiling, and see if it has 4-5 dip switches. If so, just change the settings by changing one of them, by pushing it up or down. Now, open the battery compartment of your transmitter and match the setting you just did to the receiver. BOTH have to be set on the same frequency.

What's the problem???????????? [email protected]

Here is some info: (not a full manual but spec's.http://www.quoruminternational.com/index.cfm?do=app.onlineCatalogs&catalog=fan_specsAnd when you search for additional info. use: Quorum 21542-14, the hyphen makes a difference in your searches.

Water resistant up to 90 meters means that the watch can survive a fall of 90 meters in water level.You cannot swim while wearing the watch because it can let water into the watch due to over exposure to water.

u can type the fan make and model in your computer and get them just about any where.

If it's a remote fan try completely cutting off the power at the breaker box for a minute or 2 and turn it back on. Mine does that occasionally and that seems to re-set whatever it is in the fan that causes it. Hope it helps.

That is an expensive fan. I would try to send it back to the company, and have them fix it. There should be no reason why it should be doing this. It may be the electronic control unit in the fan that went bad. It may/may not be fixable. But please don't use it until it is serviced.

I will assume you checked the batteries? These units have sequence matched signals. The only way to confirm neither has changed is to check both. It works like a garage door opener. 4 pins must match each other. On the remote, this is usually found where the battery goes. You will see the 4 pins. Up or down is the only option for each pin. That was easy. The hard part is getting to the receiver in the fan. At the ceiling there is a cover for the wires. 2 to 4 screws hold it in place. Remove the cover and you will see the receiver unit...probably stuffed in there very tight. Carefully remove the receiver to expose the pins. Check that they match the remote sequence. If they do not match correct to match and all should be good. If they match and the battereis are fresh, the remote or the receiver went bad. In which case you can get a universal, even by Hunter Fans at Home Depot or Lowes will work. Color match the wires if you are a DIY'r. Feedback is appreciated if this helped or not.

Pas sûr que vous voulez dire?

Try this site:

http://lightingbygregory.com/lighting/product/qr-7-1100-04.html?lbgc=biz_184052

Hope this helps, and please rate my answer, good or bad.

Good luck!