Norcent Technologies Popular Questions, Answers, Tips & Manuals

try a factory reset. it may be a fault when turning on. also it can happen more if left in standby mode. every now and then turn the power off completely overnight, this will discharge the capacitors and remove the static build up that can affect the bios of the tv.

I don't know does it?

Have you looked on eBay ?

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

put tv on blue screen and leave it on blue screen for a few hours it should clean up the burn in abit. on some screens they don't like to have the same screen on and no movement some tvs have a built in screen adjuster it flickers a bit so much that you dont even see it but its to stop this from happening to the screen.

Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size. Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

That might be a factory fault don't hesitate but to take it to the retailer if still under guarantee. Or phone the manufacture for a quick respond.

Input options can't be accessed without the remote. You can order a new one for most model and makes here. 1 800 Remotes Factory original replacement remote controls

1 800 Remotes Factory original replacement remote controls

You will need an HDMI to DVI adapter with audio. The DVI end of the cable should have both the DVI connection as well as a 3.5mm audio jack. You would then plug your speakers directly into the jack. If the jack is a male connector, you will need a female-to-female coupler.

It would be so costly to do it would be a totally uneconomic proposition versus buying a new unit with multiple HDMI connections.

http://www.remotes.com/SearchResults.asp?Search=+DP312 original no longer available from manufacturer but a replacement that does all the same things is being offered by Norcent

What remote? For what? Any computer store sells remotes.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Disassemble procedure to many popular brand TVs and other devices are given in detail with illustrations.

As long as you use a SD card it should work. But now most stores only sell SDHC cards and already there are lots of SDXC cards. Both won't work in the Norcent Xias. Once there were 4 Gbyte SD cards now the 1 Gbyte cards are already SDHC, because they are faster and newer devices can use these.

It is normal.

Answered.

Already answered.

This is as close as I could come. Same series different model number, but should be the same. Take a look and let me know. Download manual

Sounds like the main power regulator board inside the TV is faulty. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.