Intex Popular Questions, Answers, Tips & Manuals

It is a pump, only motors are measured in Horsepower. I would expect the HP of this above ground combined pump and filter is so low they would be embarrassed to state. It is measured in Gallons Per Hour flow rate. https://www.google.com/search?q=Intex+673R+pump+specs ..

limited info generic answer u code doesnt show for intex their codes usually start with E this is a manual that has the trouble shooting on page 20 ------- https://www.manua.ls/intex/purespa/manual?p=1 --------- and pg 13 has the codes

Here's the manual with setup information...https://www.manua.ls/intex/purespa/manual?p=9MY bad you'll have to copy and paste the link. :(

Question edited for clarity and typos. If alarm code E97 is displayed on the control panel, it means there is a heater fuse error. If alarm code appears on the control panel, unplug and plug back in the GFCI/RCD and test the GFCI/RCD to restart the system. If the problem persists, please contact a Intex service center for assistance.

What does code E97 on my spa mean? What should I do if ...

E 97 is an error code that indicates a dry fire protection system has been activated in your Intex Pure SPA. This means that the spa has sensed that there is not enough water in the system, and it has automatically shut down the heater to prevent damage. To solve this problem, you will need to add more water to the spa. Once the water level is above the minimum level required for safe operation, the dry fire protection system should reset itself automatically. It is not recommended to run the filtration and the bubbles or jets without enough water in the system as it can cause damage to the pump and other components. Therefore, make sure to add enough water before turning on any functions of the spa. Also, make sure to check for any other causes that may have led to the water level dropping too low, such as a leak or drainage issue. If you continue to experience issues, refer to the owner's manual or contact Intex customer support for further assistance.

Question edited for clarity. 'make model (what it is) first 3 words Question moved from 'Pure Cameras'. Intex are pretty good with technical documents. 'Pure Spa' is the 'friendly name', but they all have model numbers. This https://intexfaq.ch/wp-content/uploads/2021/02/2021-SSN-Combo-Spa-28462-Control-Base-Repair-Guide.pdf Was found here. Click the IMAGES tab for lots more pictures. https://www.google.com/search?q=intex+pure+spa+wiring+diagram ..

Salt generators take, on average, around 24 hours between adding salt and the system realizing or analyzing the data. A code 92 usually means salt levels are too high, but not always. It is best to take a water sample to a pool store for analysis to truly determine if that's the case. If so, draining some water and adding fresh water are the only real ways to rectify the salinity. Best wishes and hope this helps.

test for circuit or motor failure

Question edited for clarity, name of maker. Question moved from washing machines. For water rushing out, try and block from the other side so water doesn't reach the part you are undoing. Here is a parts diagram and all the washers and O-rings. Your local pool supplier probably carries them. https://www.pools.shop/en/intex-spare-parts/whirlpool-pure-spa-bubble-small-1 More here https://www.google.com/search?q=Intex+Purespa+SB-H20+parts ..

Low Flow Error. Check valves are fully open and basket filters are clean. Videos that my help. https://www.google.com/search?q=Code+90+on+my+Intex+Salt+Water+ECO15110-2 ..

Contact Intex directly, it is under manufacturer warranty.

did you have a green pool if so sand is contaminated change sand

limited info --one if the internal bladders/cell is damaged no fix keep twist seal lubed to prevent air/water leak and can still use until another cell pops

unbolt control neck from base and check connection is tight and not corroded if good most likely control unit failed

Could be a faulty power switch, could be a board issue. Do some basic tests or call a service company.

Question edited for clarity. Question moved from Cars and Trucks. It could be many things, but one of them is not the filters :>D The heater or the Pump, or the Control Gear / GFCI. https://www.google.com/search?q=intex+hot+tub+shuts+off ..

https://www.google.com/search?q=intex+purespa+impeller&sxsrf=AOaemvJ7l9-8AVGl07owxmONpRSihGlfAw:1633987545673&source=univ&tbm=shop&tbo=u&sa=X&ved=2ahUKEwi3n-j5pcPzAhXP

Question edited for clarity (spelling) Question moved from Cars and Trucks to Intex Pool and Spa. Intex Spa temperature sensor connector! Amazon https://www.amazon.ca/Sensor-Water-Temperature-Screw-Probe/dp/B07VHLBJZ4 Intex. Every part for every model. https://intexcorp.com/replacement-parts/spas/ ..

are you sure its not e99 water temp sensor because their is no 999 code for intex -----------turn off at gfi and unplug for about 5 minutes then plug back in unit some times glitches if code comes back same then notify intex [ good luck ] of code 999--any other code can be found in manual or online ----intex purespa code === ----

Edited the question into proper written English with punctuation, sentences, capital letters and stuff :>) If it is new, have you carefully read the manual a couple of times.? It is still under warranty because it is brand new and never used. Phone the Support number and they will troubleshoot with you. If you got is from a bricks and mortar shop, phone them and they will send someone out to you. https://intexcorp.com/support/ ..