Hitachi Gst Recent Questions, Troubleshooting Help & Support

There is a fuse inside. The fuse plugs into a socket holder. The value I think is 7 amp. Verify it is good or replace with the value listed by the fuse holder. Also sometimes if the charger has an overload due to a bad battery, unplug the charger and wait about an hour then plug it in again, It might just start working

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

The T con board or the LCD panel is faulty. Can confirm BY replacing the TCON board. If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

How to Enable HDMI-CEC on Your TV, and Why You Should

www.howtogeek.com/.../how-to-enable-hdmi-cec-on-your-tv-and-why-...

Jan 16, 2015 - The devices can have some control over the TV, and the TV can have some control over ... AOC: E-link; Hitachi: HDMI-CEC (Thank you, Hitachi!) ...

How to find out if your device is HDMI CEC capable?

hdmicec.blogspot.com/.../how-to-find-out-if-your-device-is-hdmi.html

May 18, 2012 - Hitachi - HDMI-CEC ... You can control your computer with your TV'sremote control and you can set up that your laptop shuts down or goes to ...

[PDF]OG S606 U516 Eng - Hitachi Service

Read page 69 of your user manual. The color/flashing patterns of the lights indicate what is wrong with the projector: http://www.hitachi-america.us/products/consumer/digitalmedia/lcd_projectors/lineup/details/pdf/01cp-rx94_og_eng.pdf

Read your user manual, page 60. The blinking lights are codes that tell you what the problem is: http://www.hitachi-america.us/supportingdocs/forhome/DisplayTechnologiesGroup/lcdprojectors/SupportingDocuments/hitachi_x201_x301_x401_x450_um.pdf

You DON'T... There is no "tuner" input provided on the Hitachi 55PMA550E model.

The issue is within the optical engine of the projector, the polarized glass are starting to shed its coating, thus causing the yellow effect.

I guess you are looking for a MOUNT. Check for something like this at Amazon:http://www.amazon.com/Mount-It-Articulating-Mount-40-Inch-70-Inch/dp/B002CTV060

If it is out of warranty, write down the model of boards inside replace the power board, once installed power it up, and see if this does solved your previous issues, good luck