Radio Communications - Page 6 - Popular Questions, Answers, Tips & Manuals

El problema de decodificaci?n de la radio Motorola XTL5000 puede deberse a una configuraci?n incorrecta de la radio. Aseg?rate de que la radio est? configurada correctamente para la codificaci?n y decodificaci?n. Por ejemplo, aseg?rate de que los ajustes de codificaci?n sean los mismos tanto para la codificaci?n como para la decodificaci?n. Tambi?n debes asegurarte de que la radio est? configurada en la misma frecuencia de la otra radio. Si esto no soluciona el problema, prueba la antena para asegurarte de que est? funcionando correctamente. Si la antena est? bien, podr?as necesitar reemplazar la placa de circuito impreso (PCB) del receptor para solucionar el problema.

Kindly check the link. http://fclosedhomes.blogspot.com/2010/10/use-bellsouth-22502260-walkie-talkie.html Thanks

To install a barrel pin jack in a RadioShack Pro-2034 police scanner, you will need to follow these steps:

1. Locate the appropriate input/output port on the back of the scanner. This is typically a 3.5mm or 1/8-inch jack.
2. Gather the necessary tools and materials. You will need a small Phillips head screwdriver, a barrel pin jack, and any connecting wires or cables that are required.
3. Carefully remove the back panel or cover of the scanner to access the internal components.
4. Locate the input/output port on the circuit board inside the scanner.
5. Carefully disconnect any existing wires or cables that are connected to the port.
6. Connect the barrel pin jack to the circuit board using the appropriate wires or cables. Make sure to follow the wiring diagram or instructions provided with the jack to ensure proper connection.
7. Secure the jack in place using the screws provided, or by soldering the connections if required.
8. Replace the back panel or cover of the scanner and test the new barrel pin jack to ensure it is functioning correctly.

It is important to follow the manufacturer's instructions and use caution when installing any components or making modifications to your scanner. If you are unsure about any aspect of the installation process, it is recommended to seek the assistance of a qualified technician or the manufacturer.

Question edited into english. No modifications. The range is restricted and the calls are encrypted.

It should just connect with the plug eBay states. This is a brand new Workman replacement omni-directional CB radio microphone. Features a 5-pin connector and a flexible coiled cord. Wiring:

Pin 1 - Audio

Pin 2 - Ground

Pin 3 - RX

Pin 4 - Common

Pin 5 - TX

Compatible Radios:

Cobra 90LTD

Cobra 140GTL

Cobra 142GTL

Cobra 148GTL

Cobra 148-F-GTL

Cobra 2000GTL

Cobra 2010

Uniden Washington

Uniden Grant XL

Uniden Madison

https://www.google.com/search?q=connect+Superstar+507-5+microphone+to+a+Uniden+Washington ..

no factory reset --this is user manual page 36 is trouble shooting ----https://www.manualslib.com/products/Radio-Shack-Pro-135-3101070.html

1. Make sure the volume on the headset is turned up.
2. Check the settings on your phone to ensure that the ringtone volume is turned up and that the ringtone is not set to vibrate only.
3. Make sure the headset is properly paired and connected to your phone.
4. Check the battery level on the headset. If the battery is low, charge the headset.
5. If none of the above steps resolve the issue, you can try resetting the headset to its factory settings.

If none of these steps resolve the issue, you should contact Plantronics customer support for further assistance.

Question edited for full 'make model (what is is)'. Question moved from Computers to make model category. I feel this is a bit specialized for the experts we have at present but at least I put it in the right place. I could find anything specific, but i did find the technical manual. http://www.repeater-builder.com/yvs/pdfs/yaesu-ft-950-technical-supplement.pdf These might provide experienced help. https://www.google.com/search?q=Yaesu+forums ..

Based on the information you provided, it seems like the Kenwood TK-2000 radios you have may have been programmed with the wrong band split. The TK-2000 is available in both VHF and UHF frequency ranges, and it's possible that the radios you have are actually UHF models, despite being listed as VHF frequencies when you read the radios. To check if your radios are UHF or VHF, look for a label on the back of the radio that specifies the frequency range. If it says UHF, then the radios can only accept frequencies in the 400-440 MHz range. If it says VHF, then the radios should be able to accept frequencies in the VHF frequency range. If you've confirmed that the radios are indeed VHF models, then it's possible that the band split settings may need to be adjusted in the programming software to match the specific VHF frequencies you're trying to program. I recommend checking the manual for your programming software to ensure that you have selected the correct band split settings before programming the radios. If you're still having issues, it may be helpful to contact Kenwood customer support for further assistance.

There are a few things you can try to troubleshoot this issue with your 2013 Chrysler 300c's Uconnect Bluetooth system:

1. Make sure that your phone's Bluetooth is turned on and that it is in pairing mode.
2. Check the Uconnect system's settings to ensure that Bluetooth is turned on and that it is set to discoverable mode.
3. Try restarting both the Uconnect system and your phone to see if that resolves the issue.
4. Check the vehicle's manual to see if there are any specific instructions for pairing a device with the Uconnect system.
5. If the above steps don't work, try clearing the Uconnect system's memory of previously paired devices, and then try pairing your phone again.
6. Check if the software of the Uconnect system is up-to-date, if not update the software.
7. Try deleting all previously paired devices on the Uconnect system, and then try pairing your phone.

If none of these steps resolve the issue, it may be a problem with the Uconnect system itself and you may need to take your vehicle to a Chrysler dealership for further assistance.

Hi, please update your power source and move your device away from anything that deals with using frequencies like other radios, microwaves, active walkie talkies or antennas. Being close to these things could cause interference with your device leading to the buzzing that you're hearing. Thank you

It appears you can. Normally you load the software to the new PC and then copy the data file to USB and transfer it. It would be a file in USERS. Then reboot the computer. https://www.google.com/search?q=gs3000+scanner+on+one+PC%2C+transfer+that+data+to+a+new+PC ..

Usually because the purchaser didn't read the instructions or because the instructions are badly written from Chinese. This is an eBay special. I wrote this Tip on connecting Bluetooth devices which mentions the step that is always missed. https://www.fixya.com/support/r26362721-pairing_bluetooth_devices

iEssentials Bluetooth FP1 Headset, USB Car Charger ...

https://www.ebay.com > itm iEssentials Bluetooth FP1 Headset, USB Car Charger Included ( IE-HFBLU-FP1 ) · Item Information · Item specifics · Shipping and handling · Sales Tax for an item # ... US$12.95 · ‎In stock

Hi, since re-pairing caused this, please perform another re-pair and check for the pre-sounds beeps again. I'm guessing that you might have accidentally skipped a step in your first attempt and it led to this sound occurring. Thank you.

Check your battery contacts. Clean with a pencil eraser. If this does not solve the problem described then your radio is in need of repair.

It sounds like you are having an issue with your GP339 radio where the PTT (Push-To-Talk) switch is not transmitting when pressed. Here are a few potential solutions to try:

1. Check the battery: Make sure that the battery is fully charged and properly installed in the radio.
2. Check the antenna: Make sure that the antenna is properly connected and not damaged.
3. Check the settings: Make sure that the radio is set to the correct frequency and that the PTT switch is configured correctly in the settings.
4. Check the microphone: Make sure that the microphone is properly connected and not damaged.
5. Check the programming: Make sure that the radio is properly programmed with the correct settings, including the correct channels and frequencies.
6. Check for physical damage: Make sure that the radio does not have any physical damage, such as a broken switch or damaged wiring.
7. Check that the radio is programmed for the correct channel.
8. Check that the radio is not in "Low Power" mode, if so, switch it to "high power" mode.

If these steps do not resolve the issue, it may be necessary to contact the manufacturer or a professional radio technician for further assistance.

Question edited to what I think you thought you were saying. I would think the answer is no. This is a high end marine radio by the best maker. It looks to be part of a two piece set up. Single Sideband is used when you are in the middle of the ocean and is made for distance. I will edit your other post and leave it up in case anyone else wants to add anything. Click on Product Support for manuals etc. https://www.furunousa.com/en/products/fs1503 ..

Hi, Please ensure that the product has no limit on the brand of batteries that can be used in it. If you can, please stick to the same brand that was initially used by your dictaphone. If these brand of batteries do not work, I would call philips to ask about the nearest repair vendor to you. That vendor should be able to troubelshoot and fix your Philips device. Thank you.

Question edited for clarity. How do I change the language on my BlueAnt st3? November 2, 2021 by anstoall2021 How do I change the language on my BlueAnt st3? From off, press and hold the On / Off button until the Bluetooth® indicator turns blinking red/blue. (The kit is now in pairing mode). Please be patient because the Commute 3 has 12 languages and it will cycle all available languages. How do I reset my BlueAnt ST3? Reset the BlueAnt device. Press and release the "Vol +," "Vol -" and "Multi-Function" buttons all at the same time. The volume buttons are located on the side of the BlueAnt, while the Multi-Function button is on the front. The BlueAnt resets and clears the existing pairing list. How do I remove a BlueAnt pair list? On your phone bluetooth menu, search for devices and select BlueAnt ST3 then enter 0000 as pincode. Press the MFB until the LED blinks red/blue. Note: Blackberry and Smart phone owners please refer to section F of user guide. Alleant Phonebook transfer will be initiated. How do I pair my Supertooth 2? Pairing Mode. Turn on its Bluetooth function then execute a Bluetooth search so that it will be able to search and find your Supertooth II. When the phone displays the list of the Bluetooth devices it has found, select the name of this kit (Supertooth II). 5. When the phone asks for a passcode, enter "0000".https://www.google.com/search?q=blueant+st3+change+language..